When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Livnitup I'm sure I missed it somewhere in this thread, but what exactly is 726-03-01... (Factory Mode enabled/disabled)?
It's just a mode they put the truck in during the assembly line as components are being installed. I think it prevents the truck from freaking out with warnings and disables a lot of stuff having to do with battery draw. It has no practical use for us.
Is there a list that shows all the mods that we can make? (588 pages on this forum is making it hard to find). My new 2017 F-150 (502A, Tech Package, etc) will be here in 2 weeks and I want to figure out all the changes I want, like disable horn honk we leaving truck and disable fake engine noise.
Can I make the dealer do the changes before I agree to accept the truck?
Is there a list that shows all the mods that we can make? (588 pages on this forum is making it hard to find). My new 2017 F-150 (502A, Tech Package, etc) will be here in 2 weeks and I want to figure out all the changes I want, like disable horn honk we leaving truck and disable fake engine noise.
Can I make the dealer do the changes before I agree to accept the truck?
Hey guys, I'm trying to tidy up my 8" MFT install. I have all the DTC corrections figured out except this one. The FCIM is looking for a Left Front Seat Heater Sensor. All I can find in the google sheets is snow plow addresses. Can anybody give me advice on how to chase this down?
Hey guys, I'm trying to tidy up my 8" MFT install. I have all the DTC corrections figured out except this one. The FCIM is looking for a Left Front Seat Heater Sensor. All I can find in the google sheets is snow plow addresses. Can anybody give me advice on how to chase this down?
PM me your email address please. I'm working on something in my FCIM and I'd like to get your .ab file for that module. Maybe we can help each other.
Hey guys, I'm trying to tidy up my 8" MFT install. I have all the DTC corrections figured out except this one. The FCIM is looking for a Left Front Seat Heater Sensor. All I can find in the google sheets is snow plow addresses. Can anybody give me advice on how to chase this down?
7A7-01-01 xxxx Xxxx xxxx
do you have an 8 or a C where that X is? If so, make it a 0. 8= Heated Seats, C=AC/Heated Seats. See if that helps.
The values in 7A7-01-03 second and third boxes are the heated seat temps for vehicles that are heated seats only (no AC seats).
For each of the 3 seat temp choices
Heated steering wheel is in first box of 7A7-01-02
do you have an 8 or a C where that X is? If so, make it a 0. 8= Heated Seats, C=AC/Heated Seats. See if that helps.
The values in 7A7-01-03 second and third boxes are the heated seat temps for vehicles that are heated seats only (no AC seats).
For each of the 3 seat temp choices
Heated steering wheel is in first box of 7A7-01-02
OK, so on the same vein...I upgraded my XLT 302a FCIM to one from a lariat sport. Only thing that wasn't working was my heated seats. I made the change you described and I'm testing now. I think they're heating up but I'm not sure if it's my body playing tricks on me. I have it on full and they used to get quite hot quickly on full. What I'm feeling now is gradual.
Oddly, my original FCIM had a 0 in that spot even though I had heated seats. Are there different settings for different fcims?
Is there a top limit on those temps? I'm assuming 6e = 110*?
Were these tested on F-150s, or are they just Dan's findings?
1) 726-32-01 xxxx xxxx **xx - Approach Light Show Max Time
2) 726-15-02 0101 0101 0145 - Auto relock enabled
I've double, triple, and quadruple checked my entries, and cannot get auto-RElock to work, or adjust the approach light timeout, which stays at 25 seconds (the original value / hex 17) no matter what. Are BCM changes sometimes finicky and take a few power cycles? I'm totally at a loss. My raw memory blocks are:
You're note alone. I have a 2017 as well and can not get the auto re-lock enabled either. The values are being stored correctly. Must be some minor change in the module that is preventing this from occurring. All other Forscan changes I've tried have worked though.
01-28-2017, 01:50 PM
