ZEN-A2B B&O Stereo integration?
#201
Senior Member
Thanks! I should have thought of that - tested my home audio speakers a long while back this way.
I have a meter and 50hz tone file (got it, pink noise, and 1000hz off Kicker's web site). I'll disconnect the RCA from my sub amp, plug it in to my meter, then measure with the 50hz tone.
I have a meter and 50hz tone file (got it, pink noise, and 1000hz off Kicker's web site). I'll disconnect the RCA from my sub amp, plug it in to my meter, then measure with the 50hz tone.
#202
Originally Posted by planetix
Thanks! I should have thought of that - tested my home audio speakers a long while back this way.
I have a meter and 50hz tone file (got it, pink noise, and 1000hz off Kicker's web site). I'll disconnect the RCA from my sub amp, plug it in to my meter, then measure with the 50hz tone.
I have a meter and 50hz tone file (got it, pink noise, and 1000hz off Kicker's web site). I'll disconnect the RCA from my sub amp, plug it in to my meter, then measure with the 50hz tone.
#203
Senior Member
Been awhile since I've done this so to check:
For pre-out I want to use AC correct?
Put the positive lead inside the rca jack and touch negative to the outside shielding? Testing the single pre-out on the Audison.
For pre-out I want to use AC correct?
Put the positive lead inside the rca jack and touch negative to the outside shielding? Testing the single pre-out on the Audison.
#204
Yes that is correct. You want AC 200. I would recommend making an rca to multimeter lead adaptor. Takes a couple minutes and a soldering iron. It's a great tool to have for testing!
Positive lead always goes to the pin, ground goes to the shield/outer ring of the rca connector.
Positive lead always goes to the pin, ground goes to the shield/outer ring of the rca connector.
Last edited by dhmcfadin; 07-11-2018 at 02:52 PM.
The following users liked this post:
Wyo11Scab (07-12-2018)
#205
Hey Moni,
I just updated the unit via my pc but I followed the instructions listed in the text file dated 07/12/2018 but after looking through this thread, I noticed the instructions listed didn't match your instructions back a couple pages. You stated we needed to plug it into the truck, wait for the green light, and then take it back to the computer to update it or the unit would have to be sent back to you for repair. Did I mess my unit up? Unfortunately, I don't have my system built yet to test.
Edit: just found the most recent update instructions and installed 2.0.0 before installing Zen V2. Looks like I will shipping back to you. Damn it.
I just updated the unit via my pc but I followed the instructions listed in the text file dated 07/12/2018 but after looking through this thread, I noticed the instructions listed didn't match your instructions back a couple pages. You stated we needed to plug it into the truck, wait for the green light, and then take it back to the computer to update it or the unit would have to be sent back to you for repair. Did I mess my unit up? Unfortunately, I don't have my system built yet to test.
Edit: just found the most recent update instructions and installed 2.0.0 before installing Zen V2. Looks like I will shipping back to you. Damn it.
Last edited by dhmcfadin; 07-12-2018 at 11:00 PM.
#207
#208
So I re-installed the update according the most recent instructions and then I connected the unit to power with some alligator clips. I got the blue and then green flashing lights. Then I went back to my computer and did the 2.0.8 update and got the green success bar. Then I plugged it back into power and now the unit gives me one blue flash then the red optical light turns on and then off. Then it just goes dark. Did I brick the unit?
#209
Senior Member
I don't know if you are going to see the correct light sequence absent the unit being able to read the CAN bus. When it starts it blinks (green or blue, I forget) when initializing on the bus, which is very quick, then goes solid blue when active and communicating with the bus. That's the normal operating state when it is on and fully hooked up.
I had one get stuck in bootloader mode, which is a constant rapid blue flash. That's a sign of a problem for sure if you see that. So I don't know that you bricked it but I am sure you can call them and ask - probably hard for them to troubleshoot until you have it hooked up in the vehicle though.
I had one get stuck in bootloader mode, which is a constant rapid blue flash. That's a sign of a problem for sure if you see that. So I don't know that you bricked it but I am sure you can call them and ask - probably hard for them to troubleshoot until you have it hooked up in the vehicle though.
The following users liked this post:
dhmcfadin (07-17-2018)
#210
--
Last edited by dhmcfadin; 07-19-2018 at 12:19 AM.