Custom Paramount Grille build
#21
Amber LEDs - $10 sourced from Amazon
Did you look at ?
Others looking at the paramount mods suggested these, but I never heard if they were the right color.
#22
Were there any part numbers on the camera mount you glued into the grill? I'm thinking I'd like to buy one to play with, so I don't ruin the current one in case I mess it up, and so I can leave what's on the truck alone until this is ready.
I'm thinking I need the front and rear brackets (Looking at this overview, I'm thinking I need this (front bracket) and this (rear bracket)) to be safe (about $20 in parts)
These are 2016 part #'s, but tasca doesn't have 2017 f150 parts yet. I doubt they changed, but would like to be sure.
I'm thinking I need the front and rear brackets (Looking at this overview, I'm thinking I need this (front bracket) and this (rear bracket)) to be safe (about $20 in parts)
These are 2016 part #'s, but tasca doesn't have 2017 f150 parts yet. I doubt they changed, but would like to be sure.
#23
Were there any part numbers on the camera mount you glued into the grill? I'm thinking I'd like to buy one to play with, so I don't ruin the current one in case I mess it up, and so I can leave what's on the truck alone until this is ready.
I'm thinking I need the front and rear brackets (Looking at this overview, I'm thinking I need this (front bracket) and this (rear bracket)) to be safe (about $20 in parts)
These are 2016 part #'s, but tasca doesn't have 2017 f150 parts yet. I doubt they changed, but would like to be sure.
I'm thinking I need the front and rear brackets (Looking at this overview, I'm thinking I need this (front bracket) and this (rear bracket)) to be safe (about $20 in parts)
These are 2016 part #'s, but tasca doesn't have 2017 f150 parts yet. I doubt they changed, but would like to be sure.
#24
Flaccid Member
Thread Starter
I have opened the amber housings supplied with the grille and installed amber LED strips. I don't really like them, so I'm going to hack up the round LEDs and install them into the housings instead.
I didn't look at your links--this is the part that I cut up to install into the grille.
GL3Z-19H421-A
This part is paired with a back piece that, when screwed together, hold the camera in place from the front and back. I'm using only the front piece, and will secure the camera with some silicone.
Correct.
GL3Z-19H421-A
This part is paired with a back piece that, when screwed together, hold the camera in place from the front and back. I'm using only the front piece, and will secure the camera with some silicone.
Correct.
Last edited by DeltaNu1142; 02-10-2017 at 01:58 PM.
#25
Flaccid Member
Thread Starter
I installed the grille today. It looks as I had hoped, but the area around the emblem isn't as polished as I wanted. The putty didn't take the paint well. But from more than a couple feet away, it looks great. I haven't connected the grille lights yet, but I have headlights coming later this week and I can do it then.
I used a Dremel to square off the amber LEDs, and then hot glued them into the housings.
The emblems is literally held to the grille by one zip tie. I cut a notch in the back of the emblem, and it's in there good & tight. So I see no reason to mess with it.
The photo is bad, but I was in a hurry. I'll get more later.
I used a Dremel to square off the amber LEDs, and then hot glued them into the housings.
The emblems is literally held to the grille by one zip tie. I cut a notch in the back of the emblem, and it's in there good & tight. So I see no reason to mess with it.
The photo is bad, but I was in a hurry. I'll get more later.
The following users liked this post:
Maybz88 (02-23-2017)
#27
I wish they made a version of that grill without the LEDs.
i.e. like this, from a 2018 sport:
I guess you could take out the leds and fill the holes and sand it smooth before painting it, but I'm not so sure what to fill it with.
i.e. like this, from a 2018 sport:
I guess you could take out the leds and fill the holes and sand it smooth before painting it, but I'm not so sure what to fill it with.
#29
Senior Member
Great job, Deltanu. I had this idea in my head for a little bit, nice to see someone actually do it.
OneLap, are you talking about something like this?
http://www.ebay.com/itm/EAG-Raptor-S...hYq53v&vxp=mtr
You might be able to get some type of spray foam, spray it in there, sand it down and then throw a little bondo over it and paint it.
Interesting. I wasn't aware they made a full mesh version. I prefer the lights and the lower portion of the Paramount design to the GalaxyMoto, and had I seen the full mesh model when I started shopping for a grill, I might have bought that one instead.
While I like the FORD letters on my Paramount, I would like to find a plastic fabricator to build a single bar cover with accommodation to mount the blue oval. I think t would look great with the mesh background. Would also keep me from having to remount my front camera, which I'd prefer to not have to do again. I tried fabricating something like this using the center bar from my Lariat sport grill, but it didn't work out.
Great work so far.
While I like the FORD letters on my Paramount, I would like to find a plastic fabricator to build a single bar cover with accommodation to mount the blue oval. I think t would look great with the mesh background. Would also keep me from having to remount my front camera, which I'd prefer to not have to do again. I tried fabricating something like this using the center bar from my Lariat sport grill, but it didn't work out.
Great work so far.
http://www.ebay.com/itm/EAG-Raptor-S...hYq53v&vxp=mtr
You might be able to get some type of spray foam, spray it in there, sand it down and then throw a little bondo over it and paint it.
Last edited by BShadows; 02-23-2017 at 12:33 PM.
#30
Senior Member
Great job, Deltanu. I had this idea in my head for a little bit, nice to see someone actually do it.
OneLap, are you talking about something like this?
http://www.ebay.com/itm/EAG-Raptor-S...hYq53v&vxp=mtr
OneLap, are you talking about something like this?
http://www.ebay.com/itm/EAG-Raptor-S...hYq53v&vxp=mtr