CB install *PICS
05-20-2010, 01:20 AM
#1
SoCal Thread Shredder
Thread Starter
Join Date: Jun 2009
Location: SoCal
Posts: 2,014
Likes: 0
Received 0 Likes
on
0 Posts
CB install *PICS
got it today and i had to install it but i am waiting for the antenna cable and adapter
BTW: thanks leo and get better soon...and i couldnt wait to put it in
before
during
some parts
after
BTW: thanks leo and get better soon...and i couldnt wait to put it in
before
during
some parts
after
05-20-2010, 01:32 AM
#2
Dude thats pretty bad *** man.Should have done a write up as i would love to put mine their,but wouldnt even know where to start without screwing something up,lol. By any chance sometime you want to a step by step thing on what ya did?
05-20-2010, 01:40 AM
#3
SoCal Thread Shredder
Thread Starter
Join Date: Jun 2009
Location: SoCal
Posts: 2,014
Likes: 0
Received 0 Likes
on
0 Posts
im not that great at describing what i did but ill try my best
stuff i needed
1.power drill
2. cutters
3. file..to file down the flastic to make it fit as tight as possible
4. pliers
and thats pretty much what you need
i took the outside frame out as you can see then the part where the cigarette lighters used to be i pooped it out and there was some plastic pieces in there that i should of took a pic of but didnt..sorry
then i cut out slowly until i got the exact size in for the cb radio..ill take more pics tomorrow or friday when i take it apart again for the antenna cable and for the positive and negative.."need to hook those up"... then filed it down to exact size.....i got the mounting bracked and cut it into to so it would be half and half on each size.......then had to twist the brackets to make it fit right...put it back on and cut the plastic side pieces so it would look as origional as possible...
you most likely wont understand my steps because i am probable confusing but i will try and take more pics tomorrow when i take it apart of the bracket and the side plastic pieces
stuff i needed
1.power drill
2. cutters
3. file..to file down the flastic to make it fit as tight as possible
4. pliers
and thats pretty much what you need
i took the outside frame out as you can see then the part where the cigarette lighters used to be i pooped it out and there was some plastic pieces in there that i should of took a pic of but didnt..sorry
then i cut out slowly until i got the exact size in for the cb radio..ill take more pics tomorrow or friday when i take it apart again for the antenna cable and for the positive and negative.."need to hook those up"... then filed it down to exact size.....i got the mounting bracked and cut it into to so it would be half and half on each size.......then had to twist the brackets to make it fit right...put it back on and cut the plastic side pieces so it would look as origional as possible...
you most likely wont understand my steps because i am probable confusing but i will try and take more pics tomorrow when i take it apart of the bracket and the side plastic pieces
05-21-2010, 02:48 AM
#4
SoCal Thread Shredder
Thread Starter
Join Date: Jun 2009
Location: SoCal
Posts: 2,014
Likes: 0
Received 0 Likes
on
0 Posts
and today the cable came in so i wired the whole thing and now waiting for the adapter for the antenna..thats tomorrow....these are some updated pics
Trending Topics
05-21-2010, 05:09 PM
#8
This is off subject but what is that between the vent and mic, to the left of the fan control. It is on the opposite side of the 12V accessory plug and is a similar size but I can't find what it is in my manual. Thanks.
05-21-2010, 11:18 PM
#10
Senior Member
its a coin holder.... in the 4x4 models that where the switch to engage 4wd goes. i have a floor shifter in my 4x4 so i had the coin holder as well....