Friday morning my truck wouldnt start, I belive brake fluid ruined my previous ABS module (kept popping both 50A jcase fuses for EBB) So I installed a different EBB from a salvage yard and the truck still wont start. All the codes in forescan are ABS related. I have been told by two people that the truck wont start until the ABS is reprogramed and was told by 3 people it should still start and drive, you just wont have ABS.

Does anyone know for sure if a push to start 2021 F150 should run even without a reprogrammed EBB? Or do I have another issue now?

 

The ABS module has the VIN written in it's configuration. At the very least, you would need to flash the configuration from your OEM ABS module onto it. Do you have FORScan?

 

Thank you for the reply! The OEM EBB is a brick, the truck doesn't even see it anymore. And yup I have Forscan thats how I was able to get to this point.

 

Pull your ab data from here:

https://www.motorcraftservice.com/AsBuilt

Plug in FORScan and go to ABS ab data, scroll to the bottom and click write all and selece the file you downloaded from above. This will write the data from the old module to the new one.

 

I just remembered that I have the latest files for the ABS. If the one you put in is on old firmware, I can help you update it, but you need the beta version of FORScan to do it.

 

Could this be casuing the immobilizer to prevent the start?

finally got the truck back from the shop because they quit on it.

They said they updated the firmware of the ABS module,

These three things are preventing it from starting:
SS_DISABL_00
SS_DISABL_01
STRT_BLCK_A_08

Below is the raw code:
===PCM DTC None===
Successful DTC reading, no error codes found

Module: Powertrain Control Module

===END PCM DTC None===

===OBDII DTC None===
Successful DTC reading, no error codes found

Module: On Board Diagnostic II

===END OBDII DTC None===

===APIM DTC None===
Successful DTC reading, no error codes found

Module: Accessory Protocol Interface Module

===END APIM DTC None===

===SODR DTC None===
Successful DTC reading, no error codes found

Module: Side Obstacle Detection Control Module - Right

===END SODR DTC None===

===SODL DTC None===
Successful DTC reading, no error codes found

Module: Side Obstacle Detection Control Module - Left

===END SODL DTC None===

===ATCM DTC None===
Successful DTC reading, no error codes found

Module: All Terrain Control Module

===END ATCM DTC None===

===TRM DTC None===
Successful DTC reading, no error codes found

Module: Trailer Module

===END TRM DTC None===

===RGTM DTC None===
Successful DTC reading, no error codes found

Module: Rear Gate/Trunk Module

===END RGTM DTC None===

===OCS DTC None===
Successful DTC reading, no error codes found

Module: Occupant Classification System Module

===END OCS DTC None===

===CCM DTC None===
Successful DTC reading, no error codes found

Module: Cruise Control

===END CCM DTC None===

===TCCM DTC None===
Successful DTC reading, no error codes found

Module: Transfer Case Control Module

===END TCCM DTC None===

===ABS DTC C0062:54-AB===
Code: C0062 - Longitudinal Acceleration Sensor

Additional Fault Symptom (:54):
- Missing Calibration

Status (-AB):
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC

Module: Antilock braking system

Freeze Frame #1:
-EVENT_TIME: 137970895 s (Thu Jun 18 17:00:43 2026) - Event time
-TOTAL_DISTANCE: 125035 km - Total Distance
-MODULE_VOLTAGE: 12.3 V - Control Module Voltage
-OUTDOOR_TEMPERATURE: 37 °C - Outside temperature
-PWR_MODE_KEY: Ignition On (Position 2) - Power Mode Key State
-ECU_POWER_SUPPLY: 12.2 V - ECU Power Supply Voltage
-ECU_F_RSC: Inactive - ECU System Flags - Roll Stability Control
-ECU_F_ABS: Inactive - ECU System Flags - ABS
-ECU_F_BTCS: Inactive - ECU System Flags - Brake Traction Control System
-ECU_F_TCS: Inactive - ECU System Flags - Traction Control System
-ECU_F_AYC: Inactive - ECU System Flags - Active Yaw Control
-ECU_F_HDC: Disabled - ECU System Flags - Hill Decent Control
-ECU_F_ESC: Inactive - ECU System Flags - Engine Drag Control
-ECU_F_TSC: Inactive - ECU System Flags - Trailer Stability Control
-AYC: INACTIVE - Active Yaw Control
-ABS: INACTIVE - Antilock braking system
-BTCS: INACTIVE - Brake Traction Control System
-EDC#1: INACTIVE - Engine Drag Control
-TCS: INACTIVE - Traction control system
-BFLHP: 0.0 kPa - Brake Fluid Line Hydraulic Pressure
-BRK_F_P_R: 0.0 kPa - Brake Fluid Line Hydraulic Pressure (Raw Value)
-IFC_D703: 199 - Internal Module Fail Code

Freeze Frame #2:
-EVENT_TIME: 137970895 s (Thu Jun 18 17:00:43 2026) - Event time
-TOTAL_DISTANCE: 125035 km - Total Distance
-MODULE_VOLTAGE: 12.3 V - Control Module Voltage
-OUTDOOR_TEMPERATURE: 37 °C - Outside temperature
-PWR_MODE_KEY: Ignition On (Position 2) - Power Mode Key State
-ECU_POWER_SUPPLY: 12.2 V - ECU Power Supply Voltage
-ECU_F_RSC: Inactive - ECU System Flags - Roll Stability Control
-ECU_F_ABS: Inactive - ECU System Flags - ABS
-ECU_F_BTCS: Inactive - ECU System Flags - Brake Traction Control System
-ECU_F_TCS: Inactive - ECU System Flags - Traction Control System
-ECU_F_AYC: Inactive - ECU System Flags - Active Yaw Control
-ECU_F_HDC: Disabled - ECU System Flags - Hill Decent Control
-ECU_F_ESC: Inactive - ECU System Flags - Engine Drag Control
-ECU_F_TSC: Inactive - ECU System Flags - Trailer Stability Control
-AYC: INACTIVE - Active Yaw Control
-ABS: INACTIVE - Antilock braking system
-BTCS: INACTIVE - Brake Traction Control System
-EDC#1: INACTIVE - Engine Drag Control
-TCS: INACTIVE - Traction control system
-BFLHP: 0.0 kPa - Brake Fluid Line Hydraulic Pressure
-BRK_F_P_R: 0.0 kPa - Brake Fluid Line Hydraulic Pressure (Raw Value)
-IFC_D703: 199 - Internal Module Fail Code
===END ABS DTC C0062:54-AB===

===TCU DTC None===
Successful DTC reading, no error codes found

Module: Telematic Control Unit Module

===END TCU DTC None===

===RTM DTC None===
Successful DTC reading, no error codes found

Module: Radio Transceiver Module

===END RTM DTC None===

===DSM DTC None===
Successful DTC reading, no error codes found

Module: Driver's Seat Module

===END DSM DTC None===

===PDM DTC None===
Successful DTC reading, no error codes found

Module: Passengers Door Control Unit

===END PDM DTC None===

===DDM DTC None===
Successful DTC reading, no error codes found

Module: Drivers Door Module

===END DDM DTC None===

===RCM DTC None===
Successful DTC reading, no error codes found

Module: Restraint Control Module

===END RCM DTC None===

===HVAC DTC None===
Successful DTC reading, no error codes found

Module: Heating Ventilation Air Conditioning

===END HVAC DTC None===

===GSM DTC None===
Successful DTC reading, no error codes found

Module: Gear Shift Module

===END GSM DTC None===

===PSCM DTC None===
Successful DTC reading, no error codes found

Module: Power Steering Control Module

===END PSCM DTC None===

===ACM DTC None===
Successful DTC reading, no error codes found

Module: Audio Control Module

===END ACM DTC None===

===BdyCM DTC None===
Successful DTC reading, no error codes found

Module: Body Control Module

===END BdyCM DTC None===

===SCCM DTC None===
Successful DTC reading, no error codes found

Module: Steering Column Control Module

===END SCCM DTC None===

===IPC DTC None===
Successful DTC reading, no error codes found

Module: Instrument Panel Control Module

===END IPC DTC None===

===GWM DTC None===
Successful DTC reading, no error codes found

Module: Gateway Module A

===END GWM DTC None===

===IPMA DTC U0415:86-68===
Code: U0415 - Invalid Data Received From Anti-Lock Brake System (ABS) Control Module

Additional Fault Symptom (:86):
- Signal Invalid

Status (-68):
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete

Module: Image Processing Module A

Freeze Frame #1:
-EVENT_TIME: 137970897 s (Thu Jun 18 17:00:45 2026) - Event time
-TOTAL_DISTANCE: 125035 km - Total Distance
-OUTDOOR_TEMPERATURE: 37 °C - Outside temperature
-ECU_POWER_SUPPLY: 11.9 V - ECU Power Supply Voltage
===END IPMA DTC U0415:86-68===

===IPMA DTC B1578:78-2F===
Code: B1578 - Digital Park Assist Camera Vision System

Additional Fault Symptom (:78):
- Alignment Or Adjustment Incorrect

Status (-2F):
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC

Module: Image Processing Module A

===END IPMA DTC B1578:78-2F===

===BCMC DTC None===
Successful DTC reading, no error codes found

Module: Body Control Module C

===END BCMC DTC None===

 

@dherman304 Immobilizer? What do you mean?

Also:

These three things are preventing it from starting:
SS_DISABL_00
SS_DISABL_01
STRT_BLCK_A_08

Where are you getting this from?

 

Getting their status from PID

thats why I think its Anti-Theft related (maybe because the new ABS Module)?
STRT_BLCK_A_08 is the antitheft system stopping the start sequence

 

That I am not sure about.......I would assume the anti-theft would be managed by the BCM; not sure the ABS is part of that system.

When they say they "updated the ABS", what do they mean by that? Was the shop using FDRS?

With FORScan, plug into your truck and when it asks you if you want to use the existing profile, select no so it does a fresh scan. Go to the ABS module and post a screenshot of what you see in lines 706-01-01 through 706-01-04 and message me the VIN.