Topic Sponsor
2015 - 2020 Ford F150 General discussion on the 13th generation Ford F150 truck.
Sponsored by:
Sponsored by:

New CVF Fabrication Downtubes

Thread Tools
 
Search this Thread
 
Old 07-15-2022, 03:58 PM
  #41  
Junior Member
 
i3oosted's Avatar
 
Join Date: Feb 2021
Posts: 14
Received 2 Likes on 2 Posts
Default

Originally Posted by Bfazona
Same thing on my 2020 and no CEL after thousands of miles.
It threw a different code P0141 which is the heating element in the o2 sensor, I think its not warming up in time now. Not sure, erased it and will see if it pops up again.

EDIT* So apparently when putting on the mini cat extenders I broke the heater wire off the passenger o2 sensor, put another one on and so far so good, no CEL's.

Last edited by i3oosted; 07-17-2022 at 08:56 PM.
Old 11-25-2022, 07:41 PM
  #42  
Junior Member
 
FordApologist's Avatar
 
Join Date: Nov 2022
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Hey great write up on the install.. I just bought my CFV Downpipes utilizing that Black Friday deal.

So you used two of the defoulers per catalytic converter?

And you only need the defoulers for the o2 sensor that screw into the cats.. not the upstream sensors?

Thanks!
Old 11-25-2022, 07:44 PM
  #43  
Junior Member
 
FordApologist's Avatar
 
Join Date: Nov 2022
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by gebo21
Cheap autozone sparkplug defoulers, dorman brand. stacked 2 of them and drilled center out of the one that the o2 sensor is screwed into for clearance (9/16 hole) think they were these

Hey great write up on the install.. I just bought my CFV Downpipes utilizing that Black Friday deal.

So you used two of the defoulers per catalytic converter?

And you only need the defoulers for the o2 sensor that screw into the cats.. not the upstream sensors?

Thanks!
Old 12-18-2022, 03:21 AM
  #44  
Senior Member
Thread Starter
 
gebo21's Avatar
 
Join Date: Oct 2014
Location: Florida
Posts: 518
Received 90 Likes on 72 Posts

Default

Originally Posted by FordApologist
Hey great write up on the install.. I just bought my CFV Downpipes utilizing that Black Friday deal.

So you used two of the defoulers per catalytic converter?

And you only need the defoulers for the o2 sensor that screw into the cats.. not the upstream sensors?

Thanks!
Yes ,exactly
Old 07-31-2023, 10:47 PM
  #45  
Senior Member
 
Sweatmachine's Avatar
 
Join Date: Aug 2013
Location: Blanco, TX
Posts: 874
Received 175 Likes on 112 Posts

Default

Bumping an old thread here....I've got a P0420 and P0430 after new aftermarket cats and O2s. Is this what I need? They make several different yet similar ones...

https://www.autozone.com/ignition-tu...009/730544_0_0
Old 07-31-2023, 10:57 PM
  #46  
F150 Vendor

 
cvf-jason's Avatar
 
Join Date: Feb 2019
Location: Miami
Posts: 923
Received 36 Likes on 26 Posts
Default

Folks generally have had good luck with these when they did get a CEL:

http://www.bigdaddiesgarage.com/mini-cat-cel-fix.html

__________________
Keep in touch!
CVFab.com | Instagram | Facebook

The following users liked this post:
Sweatmachine (08-01-2023)
Old 08-01-2023, 09:59 AM
  #47  
Senior Member
 
Sweatmachine's Avatar
 
Join Date: Aug 2013
Location: Blanco, TX
Posts: 874
Received 175 Likes on 112 Posts

Default

Originally Posted by cvf-jason
Folks generally have had good luck with these when they did get a CEL:

http://www.bigdaddiesgarage.com/mini-cat-cel-fix.html
Kinda expensive though.
Old 08-01-2023, 10:48 AM
  #48  
Senior Member
 
dsg2003mach1's Avatar
 
Join Date: Aug 2012
Location: Central FL
Posts: 2,152
Received 623 Likes on 485 Posts

Default

Originally Posted by Sweatmachine
Bumping an old thread here....I've got a P0420 and P0430 after new aftermarket cats and O2s. Is this what I need? They make several different yet similar ones...

https://www.autozone.com/ignition-tu...009/730544_0_0
cant recall if that's the right part number but you can search the forum to verify. If you go this route you need 2 packs - 4 total. You have to drill out the center of two of them. The drilled one goes inside the non-drilled one. I would NOT use their little crush seal. I tried it that way and ended up with a rear sensor lean code because it was causing a small vacuum leak. The little mini cat deals may be expensive but might work better/be easier. I ended up taking out the non-foulers all together and so far after 1.5 weeks my SPD downpipes aren't throwing any codes
The following users liked this post:
Sweatmachine (08-06-2023)
Old 08-06-2023, 07:02 PM
  #49  
Senior Member
 
Sweatmachine's Avatar
 
Join Date: Aug 2013
Location: Blanco, TX
Posts: 874
Received 175 Likes on 112 Posts

Default

Originally Posted by dsg2003mach1
cant recall if that's the right part number but you can search the forum to verify. If you go this route you need 2 packs - 4 total. You have to drill out the center of two of them. The drilled one goes inside the non-drilled one. I would NOT use their little crush seal. I tried it that way and ended up with a rear sensor lean code because it was causing a small vacuum leak. The little mini cat deals may be expensive but might work better/be easier. I ended up taking out the non-foulers all together and so far after 1.5 weeks my SPD downpipes aren't throwing any codes
I ended up buying the "mini cat deals" and installed them today. Hopefully that's all she wrote with the damn codes!
Old 08-07-2023, 09:19 PM
  #50  
This space for rent
 
Twin snail putput's Avatar
 
Join Date: Nov 2017
Posts: 551
Received 401 Likes on 191 Posts
Default

Originally Posted by Sweatmachine
Kinda expensive though.
I used two of these: http://www.bigdaddiesgarage.com/straight-cel-fix.html

No Cel and it's also the only thing that didn't have an exhaust leak on my CVF downpipes, everywhere else that they could leak, did.


Quick Reply: New CVF Fabrication Downtubes



All times are GMT -4. The time now is 04:30 AM.