FORScan - software to enable/disable features in your truck
Senior Member
7D0-01-01 *xxx xxxx xxxx add two
Old Fart
I don't know why but I felt compelled to re-activate auto start/stop. Maybe it was the half a gallon difference in mpg.
It's my first day
If MPG was of any concern to me I wouldn't have bought a truck.
The following users liked this post:
ScubaKen (08-21-2017)
It's my first day
Originally Posted by Firerunner
Somebody said it was possible to install LED headlights without additional harnesses, but I can't remember who it was...BGG was working on getting the wiring figured out and mapping BCM changes but he installed Anzos for now
Originally Posted by flsdiver
If by oem leds you mean the interior oem ambient led it was me. Boostedgrey goose did it too. Several others.
Write up here.
oem-ambient-lighting-installed-2015-xlt-mft-controlled
Write up here.
oem-ambient-lighting-installed-2015-xlt-mft-controlled
Last edited by Airborne_Ape; 08-20-2017 at 11:31 PM.
The FORScan Guy
Thread Starter
I'll have to back to page 800 and read over everything again. Back in the spring someone here put factory Platinum OE LED head lights into an XLT without the Raptor Retrofit kit & harness. Then the topic went dark and some guys here are asking me about it on Facebook.
It's my first day
Originally Posted by plumkrazy80
I just did the update to OEM LED's from Halogens where I wired all the necessary inputs into the BCM at the correct locations. I programmed your stock value and I'm getting hyperflash on my turns intermittently and my high beams flicker intermittently as well. The strange thing is when the engine isn't running, everything works perfectly, and no faults are present.
I tried setting 726-24-01 XXXX XXXX X6XX, but I still get the faults and hyperflash.
The faults I currently have are B123A, B123B, and B1446.
Are there any other parameters I should try?
My truck is a 2015 Lariat FX4, Crew Cab, 501a, Built with Halogens, but attempting to upgrade to OEM LED's.
I tried setting 726-24-01 XXXX XXXX X6XX, but I still get the faults and hyperflash.
The faults I currently have are B123A, B123B, and B1446.
Are there any other parameters I should try?
My truck is a 2015 Lariat FX4, Crew Cab, 501a, Built with Halogens, but attempting to upgrade to OEM LED's.
Maybe April fools joke, but seemed legit at the time of reading. Original post date was April 1 2017.
It's my first day
This leaves me under the impression, Boosted Grey got his hands on a wiring diagram at one point from PlumKrazy80 and has OE LED headlamps in his truck as well without the RR kit.
https://www.f150forum.com/f118/2016-...4/#post5316947
https://www.f150forum.com/f118/2016-...4/#post5316947
Last edited by Airborne_Ape; 08-21-2017 at 12:03 AM.
Senior Member
iTrader: (1)
I always have my hands on a wiring diagram....or 3 Chad! lol This can be done but imho the best and easiest way is to replace the front end harness with one from a truck that has all of your options BUT led OEM headlights....THEN make the as-built changes to the BCM so that all works as should. I only shelved this because I am pressing hard to get my truck finished and ready for Slamfest 2017 in Tampa in Oct. The Anzos will tie me over til them.
Firerunner, Lucas8888, I8iridium, and a few others could easily figure this out. If they havent by late fall/winter, I will get with Firerunner and we will finish this up.
Firerunner, Lucas8888, I8iridium, and a few others could easily figure this out. If they havent by late fall/winter, I will get with Firerunner and we will finish this up.
Last edited by 2016BoostedGreyGoose; 08-21-2017 at 01:55 AM.
The following 2 users liked this post by 2016BoostedGreyGoose:
Airborne_Ape (08-24-2017),
lucas8888 (08-21-2017)
Senior Member
iTrader: (1)
Front/Rear Satellite Speakers (Internal Amp, External Variable, Fixed Line Level, Not Used, Reserved)
727-01-01 xx*x xxxx xxxx
Can we talk a lil more specifically about this?
I am thinking to get fully variable output from the oem HU when adding a DSP and amplifiers, the best/correct bit change is 5?
Anyone know and or can explain the different changes?
I mean I guess I can break out some of the measuring tools and measure the line voltage to determine what this voltage is and if it is static or variable with the volume control, but wanted to see if anyone knew or knows. I am working on custom harnesses with RCA output on all channels.
727-01-01 xx*x xxxx xxxx
Can we talk a lil more specifically about this?
I am thinking to get fully variable output from the oem HU when adding a DSP and amplifiers, the best/correct bit change is 5?
Anyone know and or can explain the different changes?
I mean I guess I can break out some of the measuring tools and measure the line voltage to determine what this voltage is and if it is static or variable with the volume control, but wanted to see if anyone knew or knows. I am working on custom harnesses with RCA output on all channels.
Last edited by 2016BoostedGreyGoose; 08-21-2017 at 02:28 AM.