Ford f150 2015 xlt add factory 360 camera system
#241
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
Storkpkp is closer to you than I am, but I'll put it in my truck if you want...
#244
Senior Member
iTrader: (2)
Wiring to the front camera is verified, power and LIN wires are both present at the connector by the hood latch on the engine side and the sub harness side.
All front and side camera wiring has been checked for continuity and correct pin locations from C2512B to the cameras. Rear camera and C2512A is all OEM since I had PTBA, aside from the 360 switch wire which has been verified.
12V Power to the front and side cameras is present with the key on.
I rewrote the values Livnitup sent me for the IPMB and performed a module reset as that's the only option I have.
I get DTC B148E:55-0B for front camera not being configured, so it appears like it's being seen, and the DTC goes away after performing the BdyCM LIN New Module Calibration. I'm still also getting C1001:78-0B and B1530:78-0B for the Vision System Camera and Trailer Aid Camera Angle being out of alignment. Occasionally I also get PDM and DDM U0208:00-0A saying Lost Communication with Seat Control Module A.
I still have not had the option to do an IPMB LIN New Module Calibration present itself, it only shows up as a BdyCM LIN New Module Calibration.
The 360 switch does nothing while in Park or Drive unless I'm moving and then gives me the message that some functions are disabled for safety. While in Reverse it will switch between some different rear views but then everything locks up until I drive around again. The only time the 360 view attempts to appear is after I've driven the truck and I then go from Drive to Reverse, but everything is blue with the exception of the front camera view which is actually showing the rear camera. I have also noticed that if the Rear Camera Delay is turned on that the image is frozen when I start moving forward, and the image also appears frozen quite often while cycling through the rear camera views.
All front and side camera wiring has been checked for continuity and correct pin locations from C2512B to the cameras. Rear camera and C2512A is all OEM since I had PTBA, aside from the 360 switch wire which has been verified.
12V Power to the front and side cameras is present with the key on.
I rewrote the values Livnitup sent me for the IPMB and performed a module reset as that's the only option I have.
I get DTC B148E:55-0B for front camera not being configured, so it appears like it's being seen, and the DTC goes away after performing the BdyCM LIN New Module Calibration. I'm still also getting C1001:78-0B and B1530:78-0B for the Vision System Camera and Trailer Aid Camera Angle being out of alignment. Occasionally I also get PDM and DDM U0208:00-0A saying Lost Communication with Seat Control Module A.
I still have not had the option to do an IPMB LIN New Module Calibration present itself, it only shows up as a BdyCM LIN New Module Calibration.
The 360 switch does nothing while in Park or Drive unless I'm moving and then gives me the message that some functions are disabled for safety. While in Reverse it will switch between some different rear views but then everything locks up until I drive around again. The only time the 360 view attempts to appear is after I've driven the truck and I then go from Drive to Reverse, but everything is blue with the exception of the front camera view which is actually showing the rear camera. I have also noticed that if the Rear Camera Delay is turned on that the image is frozen when I start moving forward, and the image also appears frozen quite often while cycling through the rear camera views.
The following users liked this post:
FX4F150MLY (10-19-2020)
#245
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
I'm beginning to think that you have a bad module.....
#247
The FORScan Guy
#249
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
#250
Senior Member
iTrader: (2)
Son of a b!@t&... Livnitup with the win! Updated FORScan to the new version and the IPMB LIN New Module Calibration came up, did that and all looks good so far! The 360 button is working as I'd expect and images are showing from all cameras. I'll button it up after lunch and do some more testing but I think we can call this case closed. Thank you all again for all of the help and brainstorming!!
The following users liked this post:
Firerunner (08-25-2018)