When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I will try to pop mine out today and look at those sensors. Do you have access to a console with moonroof/sensors? If not I'd be happy to help with any questions/measurements or whatever.
Yes, if you wouldn't mind.... I don't have direct access to the 13th gen trucks with sensors. If you can check & see if the "bezels" that house/hold the sensors in are a seperate piece or are they molded to the mesh?
If they are molded, it will be very hard to make the sensors work.
I'll stop at the dealer over the weekend too, but if you wouldn't mind checking, that would be great! You may know & see without even pulling the console down, but it just snaps in & out of place.
You can PM me or email with your results.
Thanks.
Brett
__________________
Direct email: kustomfx.info@yahoo.com
2013 F150 5.0L, Lariat SuperCrew, KustomFX Switch panel, Rigid & PIAA lighting, LED bed lights, 6" BDS suspension lift, 35" Terra Grappler G2, 18x9 Fuel wheels...much more....
How hard are these to install for someone with not a lot of technical ability? I could probably do it but the wiring part is what I'd be nervous about. And just to clarify, are these available for a non moonroof Lariat with the motion sensors and sunglass holder?
They are actually pretty easy & the new mesh replacement will be even easier.
The ends of the wiring will be labeled which switch number & power In & Power out.... so you will need to know your incoming wires of which is which.
BUT.... the "MESH REPLACEMENT" new switch panels are only for NON-Sensor equipped trucks.
If you have sensors & NO moonroof then the one that works is the exact one in this thread That El Matador started in this thread... that installs ABOVE the mesh & console & cutting your headliner will be required. Again, it's not that bad at all!
__________________
Direct email: kustomfx.info@yahoo.com
2013 F150 5.0L, Lariat SuperCrew, KustomFX Switch panel, Rigid & PIAA lighting, LED bed lights, 6" BDS suspension lift, 35" Terra Grappler G2, 18x9 Fuel wheels...much more....
If you have the power rear slider (flat 2pc mesh) then you now have this as a choice! If you have sensors in your mesh, it is up to you if you want to disconnect them and move them up & out of the way. Even though there is minimal modification, you CAN put this back to stock!!!
Pics & quick YouTube videos:
Any questions, please refer to the sales thread to keep this thread that the OP started.
If you have the power rear slider (flat 2pc mesh) then you now have this as a choice! If you have sensors in your mesh, it is up to you if you want to disconnect them and move them up & out of the way. Even though there is minimal modification, you CAN put this back to stock!!!
Pics & quick YouTube videos:
Any questions, please refer to the sales thread to keep this thread that the OP started.
What about just a cover plate without any switches? Can something like that be available? Just wondering? That mesh looks like crap!
It's is definitely possible..... but I would have to have the machine shop make them, and send them out to get anodized. on my next order from them, I will get a few made. Cost would be the same on ANY switch panel by itself and any logo you would want (if any) is still free.
Please email me.
Thanks,
Brett
__________________
Direct email: kustomfx.info@yahoo.com
2013 F150 5.0L, Lariat SuperCrew, KustomFX Switch panel, Rigid & PIAA lighting, LED bed lights, 6" BDS suspension lift, 35" Terra Grappler G2, 18x9 Fuel wheels...much more....
What's the best way to fish the wires say down to the dash or elsewhere? I've done lots,of wiring but never under the head liner.
You need to remove the A-pillar trim piece from the side that you prefer to run your power cable and wiring down.... then you fish a wire from that area to pull it back through.
It will also help to remove the flip down sunvisor too to allow any extra room and headliner droop. But it's pretty straight forward and completely do-able without trouble.
Thanks,
Brett
__________________
Direct email: kustomfx.info@yahoo.com
2013 F150 5.0L, Lariat SuperCrew, KustomFX Switch panel, Rigid & PIAA lighting, LED bed lights, 6" BDS suspension lift, 35" Terra Grappler G2, 18x9 Fuel wheels...much more....
12-20-2016, 10:48 AM
