Interior Mod Ideas
#155
Salvage Yard Pro
Do this.......a stack of cut washers, the cut on every other one turned 180* til the slack is out. The some quick set epoxy on the washer edges. Once set, your set...........until the cable end pops off. Just have to be gentle. The center hole of the washers have to be smaller than the cable end. Or at least the top washer has to be smaller. You can also make a new end (temporary) with a steel split shot fishing weight. Slide the cable through the cut in the washers to get them on the cable.
[IMG][/IMG]
[IMG][/IMG]
Last edited by unit505; 04-05-2014 at 07:51 PM.
#156
The 2950 is already gone. The keying circuit is screwed. The Kenwood comes out tomorrow weather pending. I've got a Yaesu FT857 all mode going in. All I have to do is mount the face plate mounting bracket and the radio will go behind the seat. I only operate voice, so I'll be adding a 6m antenna and probably replacing the 2m with a dual band 2/70. I had my cb in the truck, but there's literally nobody on there around here anymore so I took it out. I was doing allot of DX on 10m 'til the Ranger took a dump. I look forward to getting back on 10m with the new to me rig tomorrow. Let me know when you get your ticket and your call. Good luck. You'll pass it I'm sure.
[/URL][/IMG]
#157
Salvage Yard Pro
10m MFJ Hamstick. Half fiberglass, half steel whip. The whip slides into the fiberglass and will tune 10 & 11m (CB for those who don't know). One antenna, both bands. Get your SWR's flat at 11m and you should be around 1.5swr for 10m. $15 and no switch!
http://www.mfjenterprises.com/Produc...ctid=MFJ-1610T
http://www.mfjenterprises.com/Produc...ctid=MFJ-1610T
The following 2 users liked this post by unit505:
Klinux13 (04-05-2014),
TheCollector (04-05-2014)
#158
Senior Member
Thread Starter
Oh, your that guy! I love your interior. My truck already has power seats, mirrors, windows, locks, tilt, cruise, ect. I'm wanting to do an explorer overhead console, the deluxe visors, lighted window and lock switches, the excursion steering wheel, and lighted rear view mirror. Also eventually sound deadening the truck. But before I do all that I'm doing a 4.10 gear swap, some 31s, and a level with helpers in the rear and a bigger transmission cooler. So the interior will be put on hold.
#159
Senior Member
Thread Starter
This would be cool for an interior dash emblem...
http://ru.aliexpress.com/item/FAST-S...42889.html?s=p
I might have to think about this for my grill. Have to be careful. This is technically illegal here. No red or blue lights facing forward.
http://www.ebay.com/itm/99-06-LED-FO...-/121312106725
http://ru.aliexpress.com/item/FAST-S...42889.html?s=p
I might have to think about this for my grill. Have to be careful. This is technically illegal here. No red or blue lights facing forward.
http://www.ebay.com/itm/99-06-LED-FO...-/121312106725
#160
Senior Member
Thread Starter
Do this.......a stack of cut washers, the cut on every other one turned 180* til the slack is out. The some quick set epoxy on the washer edges. Once set, your set...........until the cable end pops off. Just have to be gentle. The center hole of the washers have to be smaller than the cable end. Or at least the top washer has to be smaller. You can also make a new end (temporary) with a steel split shot fishing weight. Slide the cable through the cut in the washers to get them on the cable.
[/URL][/IMG]
[/URL][/IMG]