Scott902

I'd love to have park lights + fogs on all the time. Unsure if thats something that can be done. 100% chance I would bork something though and my rear blinkers would end up not working lol.

DuneRunr

I’m pretty sure you can do that. You set those options as your DRL’s. Then as long as you have the DRL setting on, they will be on.

Somewhere there are discussions on how to set what you want for DRL’s. I’d start in the ForScan spreadsheet.

Scott902

As much as I'd love to, I'm far too nervous on a new truck to try anything

Jfalat

Bambi mode and change the auto heads light switch to last know position so they stay off till turned on..

Airborne_Ape

-Disabled Fog Cornering
(if you haven't done this your fog lights looks burnt out during any slight turn)
-Suppressed PowerBoost Pedestrian Alert Speaker open circuit alerts and DTCs
(because I unplugged it).
-Add American DRL menus to Canadian vehicle lighting options.
-Enabled headlight switch remember last position.
-Disabled reverse backup brake assist related chimes and prompts
-Disabled reverse backup brake assist
-Disabled Engine Automatic Shutdown after 30 minutes in idle
(only applies to non pro power equipped models)
-Disabled simulated engine sounds EQ profile
(only applies to non hybrid)
-Disabled double honk
-Added all lock options to Sync 4 vehicle menus
-Added Silent Mode toggle in Sync 4 to enable / disable dark mode on the fly
-Added Global Windows toggle to Sync 4
-Enabled DRL circuit to operate at full brightness while fog lights are on
-Suppressed all Sirius content within Sync 4 after trial period expired
-Added Trail mode to ABS mode selector
-Turn signal switch configured to single tap = single flash
-Increased heated steering wheel temperature.

Im sure there are more I can't remember..

konoplya

my traction control button is combo'd with the hazard lights button. guess i'm SOL on this mod, huh?

konoplya

do you know if these are available to change on all trims or only PB?

BadHabit

Can you elaborate on these? I don't see mention of these in the spreadsheet.

wokka

Just setup FORScan on the computer ready for tomorrow probably - one of the main things I’m looking to setup is the “glare free lighting” - I’ve been looking around but can’t see where the instruction as for this, I.e where abouts it is, whether I have to modify any spreadsheets etc - so my question is, am I jumping the gun here a little and it’s actually there in plain English for me to just enable, or have I not looked hard enough for the “how to” write up? Thank you in advance!

DuneRunr

Here are the changes required for Glare Free headlights. There are multiple modules that need to be changed so it’s not the easiest mod. Certainly not in the plain English section either.

Credit to @ROBB1 who gives a shoutout to: tonesto7 and Livnitup for paving the way.

Glare Free Menu (replaces Auto High beam) in APIM:

APIM
7D0-09-01 x1xx xxxx
7D0-09-03 xxCx xxxx

Note: a module reset in FORScan or power cycle is required for the menu to appear.

IPMA
706-01-01 xxxx xxx9

SCCM
724-04-01 xxx4 xxxx

IPC
720-01-01 xx8x xxxx
720-10-01 xxxx xxx3

HCM
734-01-01 xxxx xx01
734-01-02 x3xx xxxx

Perform one of the below in HCM depending on the specs of your truck:

Short bed No onboard scales / ccd
734-01-04 xx53 4E

Short bed with scales / ccd or Raptor
734-01-04 xx56 D1

Long bed no scales / ccd
734-01-04 xxD9 88

Long bed with scales / ccd
734-01-04 xxDC 17