Raptor shift Paddles on non-Raptor write-up
#841
Senior Member
From my previous post: "From looking at the wiring schematics, it looks like the following: at C226 upshift = 10, downshift = 9, return = 11 --- at C210 upshift = 5 (grey wire), downshift = 6 (violet wire), return = 7 (yellow wire)." I know where C210 is.... just not which wires specifically each of the 3 wires from C226 need to tap into...
Just looking behind the glove box did not tell me exactly which wires need to be tapped into..
#842
Senior Member
iTrader: (1)
I'm planning on buying the pins to connect to 226 at the SCCM. I need to know which wires to tap into at the 210 end. The first few pages of this thread do not say specifically where to connect at the 210 end.
From looking at the wiring schematics, it looks like the following: at C226 upshift = 10, downshift = 9, return = 11 --- at C210 upshift = 5 (grey wire), downshift = 6 (violet wire), return = 7 (yellow wire). Can anyone definitely confirm this for me? Again, I am dealing with a 2015, 6-spd, floor shifter.
From looking at the wiring schematics, it looks like the following: at C226 upshift = 10, downshift = 9, return = 11 --- at C210 upshift = 5 (grey wire), downshift = 6 (violet wire), return = 7 (yellow wire). Can anyone definitely confirm this for me? Again, I am dealing with a 2015, 6-spd, floor shifter.
The following users liked this post:
lariat2015 (08-08-2018)
#844
Had my raptor wheel on for 6 months or so, just been busy/lazy to get the harness installed but finally got it in last weekend and been enjoying the paddle shifters for a few days now. Had not used a soldering iron since high school but everything working as it should
The steering wheel itself is a huge upgrade, so much nicer than the normal lariat one. Still loving how it feels
Thanks again to everyone who made it possible, awesome upgrade and to BGG for the harness
The steering wheel itself is a huge upgrade, so much nicer than the normal lariat one. Still loving how it feels
Thanks again to everyone who made it possible, awesome upgrade and to BGG for the harness
#845
Senior Member
Questions about this mod. I read hundreds of posts here. I ordered a 2019 Lariat with the heated steering wheel, adaptive cruise control, blis and lane keep assist. Does the Raptor wheel support these features? I ask this because the Lariat steering wheel has sensors in it that detect your hands on the wheel gripping it correctly and if it does not sense this it will discontinue lane keeping. Also when driving in regular drive mode will the paddles down and up shift and then return to regular drive mode after a minute of not using them?
#846
forscan noob
iTrader: (1)
Questions about this mod. I read hundreds of posts here. I ordered a 2019 Lariat with the heated steering wheel, adaptive cruise control, blis and lane keep assist. Does the Raptor wheel support these features? I ask this because the Lariat steering wheel has sensors in it that detect your hands on the wheel gripping it correctly and if it does not sense this it will discontinue lane keeping. Also when driving in regular drive mode will the paddles down and up shift and then return to regular drive mode after a minute of not using them?
Last edited by redbroncokid; 08-21-2018 at 12:55 AM.
The following users liked this post:
bsedwebt (08-21-2018)
#847
I think there's definitely a sensor in the steering wheel that detects the hands. And if there isn't, it's not the steering wheel position IMO, since I can have it dead straight and no issues, and when I remove my hands, with my knee holding the wheel equally steady, it almost immediately disconnects LKA, and the no hands warning pops up on the dash. Not sure if the Raptor has all of that, but if not, it'd be a deal-breaker for me. Still not sold on that wheel. The red band would look ridiculous on my Platinum, and I much prefer the solid smooth leather of my steering wheel than the boy-racer look (perforated leather parts) of the Raptor one. Not missing the paddles that much anymore, so will probably leave it well alone. Besides, manual sucks with this crappy tranny, so all I do is lock out gears, and the lever switch is perfectly fine for that. Just want to add the PRNDM lights, but haven't seen precise instructions on how to remove all that crap and which glue to use. Until I see that, then would order the light and go at it .
Last edited by elptxjc; 08-21-2018 at 01:31 AM.
#848
Senior Member
I just ordered Ford part number HL3Z-3600-DA Raptor 2018 heated steering wheel for radar cruise control in anticipation of my 2019 Lariat coming in sometime later this year. NOW - I need the wire kit! Is this available for the 2019 model with console shifter - I guess I will tap in to the wires by the glove box.
#849
Junior Member
Now, how would this work (or not) on a truck that does not have manual mode? Id still be able to select gears with the paddles if I install the paddle harness?