When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I’m researching and considering doing this. I have 2 questions. How do you figure out the VIN specific values for the SODL modules? Also, just making sure, will this work on the standard 4” instrument cluster? Eventually I’ll probably add the 8”, just not for now.
I’m researching and considering doing this. I have 2 questions. How do you figure out the VIN specific values for the SODL modules? Also, just making sure, will this work on the standard 4” instrument cluster? Eventually I’ll probably add the 8”, just not for now.
Livnitup assisted me with the As Built data for the SODR & SODL modules. If you know the specific module addresses, your VIN# is also used in the As Built of the ABS module.
XLT's are available with BLIS and have the 4" IPC.
Last edited by tmcolegr; Oct 16, 2019 at 06:12 AM.
Livnitup assisted me with the As Built data for the SODR & SODL modules. If you know the specific module addresses, your VIN# is also used in the As Built of the ABS module.
XLT's are available with BLIS and have the 4" IPC.
Appreciate it. I’ll reach out to him when that time comes.
I am looking at adding BLIS to my 2019 STX. I have already installed the LED Tail Lamps as well as the JL3Z-13A409-G harness. As I've been reading through this thread most have been running the 4 wires from the rear of the truck up to the front C327 connector that is mounted on the LH fender wall under the hood...BUT it seems on my 2019 STX I do not have the C327 connector mounted on the fender wall (see below). Has anyone had any success wiring up BLIS on the 2019 f-150's? I guess what I should be asking is am I looking in the correct place for this connector?
Here is my male C411 (Old C405) Connector
Last edited by crazy8baller; Nov 23, 2019 at 01:02 AM.
I am looking at adding BLIS to my 2019 STX. I have already installed the LED Tail Lamps as well as the JL3Z-13A409-G harness. As I've been reading through this thread most have been running the 4 wires from the rear of the truck up to the front C327 connector that is mounted on the LH fender wall under the hood...BUT it seems on my 2019 STX I do not have the C327 connector mounted on the fender wall (see below). Has anyone had any success wiring up BLIS on the 2019 f-150's? I guess what I should be asking is am I looking in the correct place for this connector?
Ford changed the wiring for 2019. The Blis wires now go through the Black connector on the right and the C327 no longer exists. On the Black connector, you should have a Gray/Orange wire in Pin 4 and Pin 24. There should also be a Violet/Orange wire in Pin 5 and Pin 25. Those are the Blis Canbus wires that used to be in C327. Those are the four wires you need to extend to the tailgate connector (C411).
Ford changed the wiring for 2019. The Blis wires now go through the Black connector on the right and the C327 no longer exists. On the Black connector, you should have a Gray/Orange wire in Pin 4 and Pin 24. There should also be a Violet/Orange wire in Pin 5 and Pin 25. Those are the Blis Canbus wires that used to be in C327. Those are the four wires you need to extend to the tailgate connector (C411).
I am assuming since Ford decided to omit C327 that I would not have to run the CAN Bus wires from C263 like Donjuan2002 had to on his 2018 STX...I would just need to run the 4 wires from the front to back. Correct? Do you have a diagram by chance of the Black connector?
Here are some pictures I took of the black connector. I am unsure which numbers represent what pin but from what I can tell it looks like I do not have the correct wires for BLIS installed. So it looks like I will have to run wires from C263 inside of the cab to this connector.
