I got codes and meanings but what to do???
#1
Senior Member
Thread Starter
Join Date: Jan 2010
Location: Gray, GA
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
I got codes and meanings but what to do???
Ok i finally checked my koeo codes and i got them and their meanings, but i have no clue how to fix...the truck runs good so idk what to do. Any advice welcome, thanks. Its a 4.9 300 btw.
33- TPS
19-CID
14-PIP circuit
15-EEC processor
26-tranny fluid out of test phone
28-loss of primary tach?
18-IDM circuit failure
52-pwr steering pressure switch open
62-converter clutch err
Do i need to fix all, and how do i fix the main ones to make the truck run better? I am seafoaming this week also, fyi.
33- TPS
19-CID
14-PIP circuit
15-EEC processor
26-tranny fluid out of test phone
28-loss of primary tach?
18-IDM circuit failure
52-pwr steering pressure switch open
62-converter clutch err
Do i need to fix all, and how do i fix the main ones to make the truck run better? I am seafoaming this week also, fyi.
#3
Senior Member
Join Date: Jul 2008
Location: Long Beach Calimexifornia
Posts: 58,557
Received 1,162 Likes
on
647 Posts
It ain't that. It's just many of us work on monday's (for a multitude of silly reasons)! I just happen to stop home for lunch and took a peek while downing a burger. You have a little can of worm's there, that the last 5 mins. I have left won't allow me to deal w/ it adequately. You have some doozy's though! Does it run? Are any codes repeated? Using a reader or manual scan?
Last edited by ymeski56; 06-07-2010 at 05:28 PM.
#4
Senior Member
Thread Starter
Join Date: Jan 2010
Location: Gray, GA
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Ok sorry. lol. Well the truck actually runs good, i drive it everyday. The only code that repeated was 14, how expensive and long will it take to get the codes gone...atleast most of them. I got these with a manual scan.
#5
Senior Member
Join Date: Jul 2008
Location: Long Beach Calimexifornia
Posts: 58,557
Received 1,162 Likes
on
647 Posts
Normally, after seeing these codes, I'd place a penny on each windshield wiper & call a priest! It's a little unnatural for those codes to be coming from a strong running truck. Actually, all the codes point to peripheral stuff, but stuff that's normally associated w/ a non running truck. So I'm hesitant to recommend replacement of most the stuff presenting codes. I'm thinking a/some problems w/ shared grounds. PM "Just call me sean", and get his take on these codes. We may be able to pawn a few of the codes off on "operator error"! Maybe some of the other boy's will see a connective link to these codes that would still allow the truck to also run good at the same time! The #14 as an active & continuous memory code should be enough to imply your engine should not be running. Not to mention #15! The PIP & the TFI (icm) share the same power & grounds, so that would be a neck of the woods I'd be looking at.
Last edited by ymeski56; 06-07-2010 at 09:27 PM.
#6
Senior Member
Join Date: May 2010
Location: kerrlake
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
ok hehehehe sorry gosh damn at the codes .. i would unhook battery and drink a 12 pack go to bed and connect battery next morning hoped headache and codes (sum of them left) and my headache ... show us what you have pics engine and truck
Trending Topics
#9
Senior Member
Thread Starter
Join Date: Jan 2010
Location: Gray, GA
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
Ok well i drove a while today and checked the codes again and found the same codes popped up...if those are not the right symptoms for codes then what are? The truck runs good has a little bit of rough idle but not terrible...just let me know what needs to be done to get some of these codes gone.