Adding Hill Descent Control to non-FX4 trucks
#1
The FORScan Guy
Thread Starter
Adding Hill Descent Control to non-FX4 trucks
** This post was updated on 5/14/18
For those interested: today I successfully added Hill Descent Control to my 4x4 that normally only comes with the FX4. This mod consists of adding an $8 combination Hill Descent/Traction control switch and a single change to the ABS module via FORScan. The new switch is plug and play to the existing connector. I enabled it on my Platinum without any DTCs, tested this driving and it works flawlessly.
The part I installed is: http://www.tascaparts.com/oe-ford/fl3z13d730ha.
After installation of the switch, pressing it did nothing until the change in FORScan when messages on cluster started showing up.
Below is what I changed with FORScan.
ABS Module:
760-03-01 x*xx xx If you have 0 for asterisk make it 2, if 4 make it 6, if 8 make A, if C make E. (ignore whatever is where the x's are and just put the "2" in the appropriate position ** When writing the change FORScan will give a message about incorrect checksum but ignore that and continue with the write (FORScan will automatically write the correct checksum anyways)
** 2018s: ABS 760-03-01 *xxx xx if your as-built is 0, use 2, if your as-built is 1, use 3. if your as-built is D, use F
For those interested: today I successfully added Hill Descent Control to my 4x4 that normally only comes with the FX4. This mod consists of adding an $8 combination Hill Descent/Traction control switch and a single change to the ABS module via FORScan. The new switch is plug and play to the existing connector. I enabled it on my Platinum without any DTCs, tested this driving and it works flawlessly.
The part I installed is: http://www.tascaparts.com/oe-ford/fl3z13d730ha.
After installation of the switch, pressing it did nothing until the change in FORScan when messages on cluster started showing up.
Below is what I changed with FORScan.
ABS Module:
760-03-01 x*xx xx If you have 0 for asterisk make it 2, if 4 make it 6, if 8 make A, if C make E. (ignore whatever is where the x's are and just put the "2" in the appropriate position ** When writing the change FORScan will give a message about incorrect checksum but ignore that and continue with the write (FORScan will automatically write the correct checksum anyways)
** 2018s: ABS 760-03-01 *xxx xx if your as-built is 0, use 2, if your as-built is 1, use 3. if your as-built is D, use F
Last edited by Livnitup; 05-14-2018 at 12:38 PM. Reason: by request
The following 36 users liked this post by Livnitup:
2011SuperCrew (11-01-2016),
antho (11-02-2016),
Apples (03-24-2018),
B-ManFX4 (11-01-2016),
Boomer8 (07-05-2017),
and 31 others liked this post.
#4
The FORScan Guy
Thread Starter
The switch I have now has like rounded corners instead of cut corners so that's what's preventing it from sitting in flush. The left side of my current switch isn't seating in the cutout because of this (pics of current switch below). I now have 2 switches on order: 1 from Fordparts.com and 1 from Tasca so I'll confirm which is best upon arrival.
#5
One Clean Machine
iTrader: (5)
What exactly does HDC do? Tia...
#6
The FORScan Guy
Thread Starter
The following 2 users liked this post by Livnitup:
Toddman38 (11-01-2016),
toostroked (02-13-2017)
#7
Senior Member
iTrader: (1)
The switch I have now has like rounded corners instead of cut corners so that's what's preventing it from sitting in flush. The left side of my current switch isn't seating in the cutout because of this (pics of current switch below). I now have 2 switches on order: 1 from Fordparts.com and 1 from Tasca so I'll confirm which is best upon arrival.
Last edited by 2016BoostedGreyGoose; 11-01-2016 at 06:49 PM.
Trending Topics
#8
One Clean Machine
iTrader: (5)
Plus the Platty version, you have, has the Ambient Lighting leds as well.
#10
what's the part number for the console you got?