SDDesigns 2018 SCrew XLT 4X4 5.0 Supercharged "50WOT"
#941
Doesn't matter!
Thread Starter
Nice! I had a 4xD cell Mag mounted in the same location in our Tacoma. I’ve got my light mounted near the floor under the center dash of the 150.
Gotta keep all the necessities within reach these days.
Glock= check
Escape tool= check
Flashlight= check
Knife= check
Still looking for an inconspicuous place to mount the bear deterrent ( high powered pepper spray ) for “non lethal” car jacking threats.
LOL!
Gotta keep all the necessities within reach these days.
Glock= check
Escape tool= check
Flashlight= check
Knife= check
Still looking for an inconspicuous place to mount the bear deterrent ( high powered pepper spray ) for “non lethal” car jacking threats.
LOL!
Glock= not happening in NJ
Escape tool= check
Flashlight= close enough
Knife= check
I'm still holding off on the AR mount for under the rear seat, hoping to be relocating sometime in the future out of the Socialist State of New Jersey.
The following users liked this post:
McLovin (02-09-2020)
#942
Senior Member
Pretty much that entire region of the North East is ridiculous with hand gun laws, especially Maryland, New Jersey, New York, and Rhode Island. I have family all over the region and was checking everything before going to a family wedding in October in Maryland. I remember being shocked that like less than 1% of applicants actually get a CPL/CCW for those states.
The following users liked this post:
sddesigns (02-11-2020)
#943
Doesn't matter!
Thread Starter
Pretty much that entire region of the North East is ridiculous with handgun laws, especially Maryland, New Jersey, New York, and Rhode Island. I have family all over the region and was checking everything before going to a family wedding in October in Maryland. I remember being shocked that like less than 1% of applicants actually get a CPL/CCW for those states.
#944
Doesn't matter!
Thread Starter
Well, @Stage3Motorsports came through with the Morimoto XB Fog lights warranty replacements in a pretty timely manner. Now I just have to decide if they're going back on or putting them up in the market place.
The following 3 users liked this post by sddesigns:
#945
Doesn't matter!
Thread Starter
I guess it's time for some updates and the next step.
The parts are starting to roll in now, but it will still be a few weeks before everything is here.
Just the beginning.....
The parts are starting to roll in now, but it will still be a few weeks before everything is here.
Just the beginning.....
The following users liked this post:
OCMike (06-30-2020)
#946
TOTM Sept. '18
iTrader: (1)
Glad to see you're back. I've been catching up on a crap load of stuff around the house myself and the truck been is on the back burner. That's a big job, are you doing it yourself?
The following 2 users liked this post by OCMike:
johnday in BFE (06-30-2020),
sddesigns (06-30-2020)
#947
Village Sociopath
iTrader: (1)
Join Date: Jun 2014
Location: Nowhereville Barton City Michigan
Posts: 28,713
Received 10,170 Likes
on
6,575 Posts
Steve, just what are you doing?
#948
Doesn't matter!
Thread Starter
No, Rob's Performance Undertakers go to guy. He's also doing the rear diff and adding the VMP intercooler in addition to the stock Whipple intercooler.
The following users liked this post:
OCMike (06-30-2020)
#949
Doesn't matter!
Thread Starter
The following 6 users liked this post by sddesigns:
Davecn5 (06-30-2020),
Firerunner (06-30-2020),
johnday in BFE (06-30-2020),
Johnny_bravo00 (06-30-2020),
OCMike (06-30-2020),
and 1 others liked this post.
#950
Village Sociopath
iTrader: (1)
Join Date: Jun 2014
Location: Nowhereville Barton City Michigan
Posts: 28,713
Received 10,170 Likes
on
6,575 Posts