Ford F150 Forum - Community of Ford Truck Fans

Ford F150 Forum - Community of Ford Truck Fans (https://www.f150forum.com/)
-   2011+ Engine Related Questions (https://www.f150forum.com/f70/)
-   -   Borg Warner Install Thread!!! (https://www.f150forum.com/f70/borg-warner-install-thread-326950/)

raceredf150 01-15-2016 11:17 PM

Hi guys, well truck just isnt running right still. Talked to Mike at MPT today and he said my wastegates arent even working properly on my datalog. I get a quick surge of boost followed by pulsing surges of power until i let go of the gas. I looked at all hoses and all are connected and fine. Then i tested the solenoids at the bovs and the wastegate solenoid at the intake manifold and seem fine. They all open with power connected to them. So any help right now would be great as my truck barely is drivable

Willy_Wonka 01-16-2016 10:18 AM

You could load up the OEM tune and see if the problem replicates or disappears. If it replicates under the OEM tune perhaps one of the vacuum hoses has a small crack? All I got.

Kenferg1 01-17-2016 10:55 AM


Originally Posted by raceredf150 (Post 4510478)
Hi guys, well truck just isnt running right still. Talked to Mike at MPT today and he said my wastegates arent even working properly on my datalog. I get a quick surge of boost followed by pulsing surges of power until i let go of the gas. I looked at all hoses and all are connected and fine. Then i tested the solenoids at the bovs and the wastegate solenoid at the intake manifold and seem fine. They all open with power connected to them. So any help right now would be great as my truck barely is drivable

Check voltage at the waste gate solenoid. According to the dealer that replaced my harness it should be 5v. I had a defective harness that was only putting out 1.8v and it caused it to surge and dump, surge and dump. Hope this helps.

raceredf150 01-17-2016 02:59 PM


Originally Posted by Kenferg1 (Post 4512360)

Check voltage at the waste gate solenoid. According to the dealer that replaced my harness it should be 5v. I had a defective harness that was only putting out 1.8v and it caused it to surge and dump, surge and dump. Hope this helps.

Thanks ill give that a shot! Do you know how to test it? Can i disconnect the harness while the truck is running? I know my wastegates work i can blow air in the hoses and they open smoothly

Kenferg1 01-18-2016 10:29 AM


Originally Posted by raceredf150 (Post 4512686)
Thanks ill give that a shot! Do you know how to test it? Can i disconnect the harness while the truck is running? I know my wastegates work i can blow air in the hoses and they open smoothly

I'm sorry, but I don't. Maybe there's a Ford tech that can chime in.

jhunt47 01-22-2016 04:50 PM

Any luck getting your truck running better?

raceredf150 01-22-2016 07:06 PM


Originally Posted by jhunt47 (Post 4523506)
Any luck getting your truck running better?

No still not running. Got another email from Mike today. After a new wastegate solenoid the logs showed the same thing he said. Wastegate duty cycle at 0% with 7psi on that log. I dont know what else to do. Truck was fine before the install too

jhunt47 01-22-2016 08:55 PM


Originally Posted by raceredf150
No still not running. Got another email from Mike today. After a new wastegate solenoid the logs showed the same thing he said. Wastegate duty cycle at 0% with 7psi on that log. I dont know what else to do. Truck was fine before the install too

Did you try loading the stock tune? Don't run it hard but see if you could data log is to see if the waste gates are working. That might help but makes no sense as I think the waste gates vent with excessive boost right? So how can it only be running 7psi and the wast gates not working. Almost like your loosing boost. I may be wrong but if they are made to vent say at 17psi and your only getting 7 wouldn't they not have to work or show 0%?

raceredf150 01-22-2016 09:07 PM


Originally Posted by jhunt47 (Post 4523942)

Did you try loading the stock tune? Don't run it hard but see if you could data log is to see if the waste gates are working. That might help but makes no sense as I think the waste gates vent with excessive boost right? So how can it only be running 7psi and the wast gates not working. Almost like your loosing boost. I may be wrong but if they are made to vent say at 17psi and your only getting 7 wouldn't they not have to work or show 0%?

I just got a new tune from Mike that is stock but changed for my high flow y pipe. Ill data log that tomorrow. That 7psi is with a mild tune he gave because im having problems, its set for max 12psi but ive hit 14 psi with half throttle. Defiantly not losing boost it boost way too fast and hard

jhunt47 01-22-2016 09:35 PM


Originally Posted by raceredf150
I just got a new tune from Mike that is stock but changed for my high flow y pipe. Ill data log that tomorrow. That 7psi is with a mild tune he gave because im having problems, its set for max 12psi but ive hit 14 psi with half throttle. Defiantly not losing boost it boost way too fast and hard

I gotcha im at a loss now sorry.


All times are GMT -4. The time now is 12:53 PM.


© 2024 MH Sub I, LLC dba Internet Brands