Forscan applications
#3941
Senior Member
Cruise control in hilly areas might not be the best thing to begin with? Both for safety and fuel economy.
#3942
Junior Member
I haven't seen much, but it's possible I missed it or haven't found it yet. New to Forscan, and just started using. I have a 2010 F150 SuperCrew Platinum. I would like to make some mods to the truck like activate fog lights for DRLs, reset the keyless entry, etc. Is this possible? If so, anyone have a tutorial for the 2010's?
Thanks,
Doc
Thanks,
Doc
#3943
Member
Thread Starter
I haven't seen much, but it's possible I missed it or haven't found it yet. New to Forscan, and just started using. I have a 2010 F150 SuperCrew Platinum. I would like to make some mods to the truck like activate fog lights for DRLs, reset the keyless entry, etc. Is this possible? If so, anyone have a tutorial for the 2010's?
Thanks,
Doc
Thanks,
Doc
.
The following users liked this post:
docnelson (05-06-2019)
#3944
Senior Member
I am looking for some as built data for a truck with Sync 1 basic I guess for an FDIM or FCIM not sure the name if it but the display to the radio when you have a base model radio. I want to turn on my compass display. And if possible my AC fan speed. More than anything the compass. I kept my GPSM after removing Sync 1 which was an upgrade I did not original to the truck. Can someone help me out. I think it's just one line of code anyway
#3945
https://drive.google.com/open?id=1MH...Vcfi8AHM01AKJl
EDIT: Although the instructions state 2011-2012 it works for 13 and 14 as well. They discuss using IDS for changing the asbuilt data and this is because it was posted pre-Forscan. Use the values listed.
.
EDIT: Although the instructions state 2011-2012 it works for 13 and 14 as well. They discuss using IDS for changing the asbuilt data and this is because it was posted pre-Forscan. Use the values listed.
.
thanks
#3946
Member
Thread Starter
.
#3948
Member
Thread Starter
As for tire size changes, I haven't had any luck with 13 or older even using IDS and yes I own my own VCMII. I had to use an SCTx4 programmer to get my settings correct when I went from 30" to 35" tires.
.
.
#3949
okay I have been searching around on the forum and may have found how to add the key pad to the 09-10 trucks
seems to lines 726-04-01
none keypad - 726-04-01-0234
keypad - 726-04-01-0638
I haven't tried it yet, I need to pull the door apart and plug in a keypad and try and figure out what my factory code could be, from what I read it should be on the GEM. not sure if I can read it after I have changed the as-built lines but I'm going to try, worst case It doesn't work
the tire size I'm not overly concerned about just thought I would do it if I could
seems to lines 726-04-01
none keypad - 726-04-01-0234
keypad - 726-04-01-0638
I haven't tried it yet, I need to pull the door apart and plug in a keypad and try and figure out what my factory code could be, from what I read it should be on the GEM. not sure if I can read it after I have changed the as-built lines but I'm going to try, worst case It doesn't work
the tire size I'm not overly concerned about just thought I would do it if I could
#3950
Senior Member
I wonder if the PCM Relearn feature would work on changing tire size for 13 and older? I know the 15+ guys have to run that to get everything to work right. I wouldn't be able to try this because my truck programs fine with forscan via the BCM tire line. I did get a DTC for tire size mismatch though (same one 15+ guys get).