Topic Sponsor
2015 - 2020 Ford F150 General discussion on the 13th generation Ford F150 truck.
Sponsored by:
Sponsored by: Worksport

Heating issue.

Thread Tools
 
Search this Thread
 
Old Dec 8, 2025 | 09:14 PM
  #1  
Caveman@72's Avatar
Thread Starter
Junior Member
 
Joined: Dec 2025
Posts: 1
Likes: 0
Default Heating issue.

I have a 2016 F150 XLT 5.0 I am having heating issues with the driver side blowing cool air. I know this has been discussed in here in the past but I am having trouble finding the right thread. As of now I have replaced the actuator for the blend door motor on the passenger side below the glove box twice now with no luck. The truck does not have dual climate control but does have the vents in the center console and under the seats. It does help sometimes with turning on the recirculation button and when the outside temperature is above 40 degrees after driving for a while. I did just replace all hoses and water pump along with the thermostat, the system has been bled of air and the heater core was flushed and both heater hoses are hot when at operating temperature. Fan blows good and strong in which ever setting I change it to and the air will switch from floor to defrost to vents when I change them to test for movement. I do notice that when I only have the heat on the floor setting it is much cooler than the vents or defrost modes. Any help would be greatly appreciated.
Reply
Old Dec 8, 2025 | 09:46 PM
  #2  
artsr2002's Avatar
Senior Member
5 Year Member
Liked
Loved
Community Favorite
 
Joined: Jul 2018
Posts: 14,589
Likes: 8,786
From: My House
Default

Welcome to the forum.
Reply
Old Dec 9, 2025 | 08:00 AM
  #3  
SpencerPJ's Avatar
5 Year Member
5 Year Member
Community Builder
Liked
Community Favorite
 
Joined: Feb 2020
Posts: 4,115
Likes: 2,255
Default

This thread is pretty informative. Post 2 shows other actuator locations. Good luck https://www.f150forum.com/f118/front...orking-576904/
Reply
Old Dec 9, 2025 | 11:13 AM
  #4  
52merc's Avatar
5 Year Member
5 Year Member
Community Builder
Liked
Loved
 
Joined: Nov 2018
Posts: 6,715
Likes: 3,933
From: Calgary, Alberta
Default

This problem has been posted brefore and it ended up being a problem with the heater core being partially plugged. Even though there is a single temperature blend door, air going to the passenger side passes through the upper half of the core and air for the driver side passes through the lower portion.

Replacing the core is a major job so I would try to flush the core first. See post #19 of this thread.

https://www.f150forum.com/f118/no-he...ontrol-549277/
Reply
Old Dec 13, 2025 | 07:25 AM
  #5  
Kevin173490's Avatar
Junior Member
 
Joined: May 2025
Posts: 3
Likes: 0
Default

Originally Posted by Caveman@72
I have a 2016 F150 XLT 5.0 I am having heating issues with the driver side blowing cool air. I know this has been discussed in here in the past but I am having trouble finding the right thread. As of now I have replaced the actuator for the blend door motor on the passenger side below the glove box twice now with no luck. The truck does not have dual climate control but does have the vents in the center console and under the seats. It does help sometimes with turning on the recirculation button and when the outside temperature is above 40 degrees after driving for a while. I did just replace all hoses and water pump along with the thermostat, the system has been bled of air and the heater core was flushed and both heater hoses are hot when at operating temperature. Fan blows good and strong in which ever setting I change it to and the air will switch from floor to defrost to vents when I change them to test for movement. I do notice that when I only have the heat on the floor setting it is much cooler than the vents or defrost modes. Any help would be greatly appreciated.
I am having same issue. Had it to the dealer the so far have fixed a small coolant leak, drivers side actuator , and the wanted to replace the whole ac control box, but they wanted $4,000 because it is the whole HVAC system. I was not replacing the whole system. which replaces all components dampers and actuators. if I fix I will repost!. so far they charged me $1,300.
Reply




All times are GMT -4. The time now is 07:07 PM.