Ford F150 Forum - Community of Ford Truck Fans - Search Results



Showing results 1 to 8 of 8
Search took 0.07 seconds.
Search: Posts Made By: guyren
Forum: 2009 - 2014 Ford F150 09-07-2016, 05:04 PM
Replies: 198
Views: 125,380
Posted By guyren
I had this issue so I did a rear break service....

I had this issue so I did a rear break service. LCleaned and lubed up all the slider pins on the calipers, cleaned and lubed emergency break cable and lever mechanisms inside the rear drum. Truck is...
Forum: 2009 - 2014 Ford F150 04-23-2015, 07:40 PM
Replies: 0
Views: 290
Posted By guyren
2010 XTR4X4 crew trans leak?

Noticed a wet spot beneath the engine/trans, where the two mate. Looks like tranny fluid. Seen this on other trucks same vintage 4.6 engine too. Anyone here have any info on this? Bad seal or...
Forum: 2009 - 2014 Ford F150 03-17-2014, 10:41 AM
Replies: 8
Views: 4,145
Posted By guyren
I had Yakima bars from my old ride but they...

I had Yakima bars from my old ride but they wouldn't recomend the Q122 clip for my 2010 SCrew so I spent more money and bought the Thule set up. They seem to fit OK. I need them to carry by 12' ...
Forum: Towing/ Hauling/ Plowing 02-07-2014, 09:47 AM
Replies: 6
Views: 1,380
Posted By guyren
Thanks Steve. You weren't kidding about local eh!...

Thanks Steve. You weren't kidding about local eh! I am in Corbeil. I'll give them a call.
Forum: Towing/ Hauling/ Plowing 02-06-2014, 01:10 PM
Replies: 6
Views: 1,380
Posted By guyren
My old bars are stamped 750lbs and they are...

My old bars are stamped 750lbs and they are streched right to the bottom of the trailer frame (almost touching) and the back of my truck is still sagging. By buddies 800-1000 lbs husky bars barely...
Forum: Towing/ Hauling/ Plowing 02-06-2014, 12:37 PM
Replies: 6
Views: 1,380
Posted By guyren
I don't have the spec on my WDH head, no...

I don't have the spec on my WDH head, no markings. My bars don't have a label either. I've tried a friends husky bars and they snapped in fine. There are different types of spring bars as you say,...
Forum: Towing/ Hauling/ Plowing 02-06-2014, 10:20 AM
Replies: 6
Views: 1,380
Posted By guyren
Curt spring bars (weight dist.)

I am looking to replace my spring bars for my weight distribution set up. My current bars are worn out. Wondering if anyone has ever used Curt spring bars part nos. 17105 (800 lbs) or the 17106 (1000...
Forum: 2009 - 2014 Ford F150 09-25-2013, 04:09 PM
Replies: 765
Views: 144,711
Posted By guyren
Ditto. 2010 F150 screw. Happened on Sept 24. My...

Ditto. 2010 F150 screw. Happened on Sept 24. My previous truck had an automatic defrost. It turned off automatically after some time. Doesn't this one turn off automatically? Anyway, went to Ford...
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -4. The time now is 10:52 AM.


Copyright 2006 - 2017 F150Forum.com