OCMike's RCSB Guard Metallic 5.0 Build
#551
Still...
My favorite thing about his truck are the seats..
My favorite thing about his truck are the seats..
The following users liked this post:
OCMike (10-08-2018)
#552
Senior Member
Yea, me too!
I can't do the mod because we have a loving dog that sits there.
And I'm OK wiff dat. Woof!
Pecked out on my iPhone.
I can't do the mod because we have a loving dog that sits there.
And I'm OK wiff dat. Woof!
Pecked out on my iPhone.
The following users liked this post:
OCMike (10-08-2018)
#553
They'd match my trucks exterior perfectly. My seats need TLC though...
Driver side is worn out from the ole butt slide
Driver side is worn out from the ole butt slide
The following users liked this post:
OCMike (10-08-2018)
#554
TOTM Sept. '18
Thread Starter
iTrader: (1)
Thanks guys..For the kind words.
Yeah...I'm worried about dragging my butt in and out too and wearing out the seats...I really want this thing to last, the truck replaced a 18 year old SUV.
Mike
Last edited by OCMike; 10-08-2018 at 08:43 PM.
#555
Senior Member
Mike - your build has been amazing. -- the center console is something that I have been thinking about doing - sounds like a nice "while I'm on vac this Christmas" thing to do. Just need to start collecting parts now. Although, I would rather leave the shifter where it is on the column and utilize that space as a storage bin type of thing. Thanks for all of your pics and "how to's"!
#556
TOTM Sept. '18
Thread Starter
iTrader: (1)
It's actually the only reason I put steps on mine. I can get in easy enough without them, but found I was needing to slide over the seat to do it. With the steps, I just step up and sit down in the seat without the need to slide. Figured it would save the seat a bit.
Mike - your build has been amazing. -- the center console is something that I have been thinking about doing - sounds like a nice "while I'm on vac this Christmas" thing to do. Just need to start collecting parts now. Although, I would rather leave the shifter where it is on the column and utilize that space as a storage bin type of thing. Thanks for all of your pics and "how to's"!
Mike - your build has been amazing. -- the center console is something that I have been thinking about doing - sounds like a nice "while I'm on vac this Christmas" thing to do. Just need to start collecting parts now. Although, I would rather leave the shifter where it is on the column and utilize that space as a storage bin type of thing. Thanks for all of your pics and "how to's"!
Without moving the shifter the task would be really easy and little wiring. The USB cables are long enough to reach into the console so that's not hard either. You do need the two AC vents bezels and a bezel between the Sync cubby and the center stack, probably about a $100 for all.
I bought a used black donor console was from I think a 2016 truck and I believe there was a minor redesign in 2017 or 18 in front cubby area. On the older trucks the tray part cubby is part of the console, in the newer it's a separate part. Tasca's drawings to not show the correct parts so you need to order with a VIN from a truck equipped with the console.
I bought a new bare console for a 2018 (Camel) and mix and matched parts using both old and new parts. The used one was also a 6 speed and has an extra stop, so I couldn't used the shifter or panel that says PRND21, because the 10 speed says PRNDM.
Mike
The following users liked this post:
whoch (10-09-2018)
#557
TOTM Sept. '18
Thread Starter
iTrader: (1)
I have a suspicion that alanis928 is a bot?
Mike
Mike
Last edited by OCMike; 10-16-2018 at 06:46 PM.
#558
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
#559
TOTM Sept. '18
Thread Starter
iTrader: (1)
#560
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
I knew what you meant.....I noticed the wave of new posts also.
The following users liked this post:
OCMike (10-16-2018)