OCMike's RCSB Guard Metallic 5.0 Build
#531
TOTM Sept. '18
Thread Starter
iTrader: (1)
Thanks...Any word yet on your truck?
Thanks...Nothing I've done hasn't already been done by someone else first. Thanks to the folks on this forum for that.
LOL...I wish there was room...A moonroof would be sweet!
Mike
LOL...I wish there was room...A moonroof would be sweet!
Mike
Last edited by OCMike; 09-24-2018 at 09:37 PM.
#532
TOTM Sept. '18
Thread Starter
iTrader: (1)
Easy...There are a few torx on the back on each side. I bought the loaded up wheel because I though I might want to add ACC and heated wheel at some point, i'm starting to build up a parts list now. The mode buttons and phone on the right side of the Raptor wheel can't be used for anything.
Mike
Mike, in order to use the Raptor bezel you had to swap the XLT buttons onto it, right? how hard was that to do? I'm about to pull the trigger on a Raptor wheel and I'd like to use the brighter bezel too. One more question, the part # for the wheel that will fit my 2018 XLT is I believe, HL3Z-3600-AA (no heat, no adaptive CC)?
Mike
Last edited by OCMike; 09-24-2018 at 09:20 PM.
The following users liked this post:
ManMountainDean (09-24-2018)
#533
Hey Mike,
My truck showed up last week at the dealer in Cincy. Got all the paperwork this morning via UPS and sent it all back with my check
We are waiting for my Whipple to show up and then of course to get on thier install schedule. I am guessing it will still be a few weeks.
Rayo
My truck showed up last week at the dealer in Cincy. Got all the paperwork this morning via UPS and sent it all back with my check
We are waiting for my Whipple to show up and then of course to get on thier install schedule. I am guessing it will still be a few weeks.
Rayo
The following 2 users liked this post by RayoVac:
1995GreenMachine (01-06-2020),
OCMike (09-24-2018)
#534
TOTM Sept. '18
Thread Starter
iTrader: (1)
Hey Mike,
My truck showed up last week at the dealer in Cincy. Got all the paperwork this morning via UPS and sent it all back with my check
We are waiting for my Whipple to show up and then of course to get on thier install schedule. I am guessing it will still be a few weeks.
Rayo
My truck showed up last week at the dealer in Cincy. Got all the paperwork this morning via UPS and sent it all back with my check
We are waiting for my Whipple to show up and then of course to get on thier install schedule. I am guessing it will still be a few weeks.
Rayo
Mike
#535
#536
TOTM Sept. '18
Thread Starter
iTrader: (1)
#537
#538
TOTM Sept. '18
Thread Starter
iTrader: (1)
#539
Senior Member
LOL, "The cheap ones". I can't find them for less than $89 with tax and shipping. Oh well, here goes. One thing though I think my Husky mats are going to cover part of the lettering.
#540
TOTM Sept. '18
Thread Starter
iTrader: (1)
You can buy them 1 by one piece too from the parts department. Autonation White Bear Lake has them for $35/each + shipping. If your buying other parts the shipping wouldn't be too bad.
I think the part number HL3Z-1613209-AA, but check it first before ordering.
My OCD gets in the way a lot. That real carbon fiber cubby cover for the console was stupid expensive. Oh well this once in a lifetime truck.
Mike
Last edited by OCMike; 09-26-2018 at 03:16 PM.
The following users liked this post:
ManMountainDean (09-26-2018)