Krookz build
#41
Senior Member
Thread Starter
Ouch... my wallet
Busted my knee pretty bad recently when I slipped on the paint... Not happening again.
Busted my knee pretty bad recently when I slipped on the paint... Not happening again.
Last edited by Krookz; 04-23-2014 at 04:17 PM.
The following users liked this post:
badblackSTX (04-24-2014)
#42
Member
My Line-X has held up well over a couple of years, and my dad had to get it in his f150.
Like the removal of all the bumper plastic below the tow hooks, from all the trails and brush, all mine looks bent and cracked, bout to do the same.
How did you mount the bed rail LEDS if you dont mind me asking?
Like the removal of all the bumper plastic below the tow hooks, from all the trails and brush, all mine looks bent and cracked, bout to do the same.
How did you mount the bed rail LEDS if you dont mind me asking?
#43
Senior Member
Thread Starter
Hope this helps...
0425140839 by floggersg, on Flickr
0425140839a by floggersg, on Flickr
Yea... figured id pull it off before I destroy it in the woods. Still need to get those skid plates done. So much stuff to do!
The lights; I picked up a set of bull rings and made a little bracket to fit down inside. Had to trim the plastic on the ring a bit. Rings still function. I re-did the mount on the light as well so I can rotate/pivot where I need it. Looks like I need to repaint them as well
0425140837 by floggersg, on Flickr
Also here's where I mounted my little fuse block. Ill clean up the wires once I get everything installed and set.
0425140839b by floggersg, on Flickr
0425140839 by floggersg, on Flickr
0425140839a by floggersg, on Flickr
My Line-X has held up well over a couple of years, and my dad had to get it in his f150.
Like the removal of all the bumper plastic below the tow hooks, from all the trails and brush, all mine looks bent and cracked, bout to do the same.
How did you mount the bed rail LEDS if you dont mind me asking?
Like the removal of all the bumper plastic below the tow hooks, from all the trails and brush, all mine looks bent and cracked, bout to do the same.
How did you mount the bed rail LEDS if you dont mind me asking?
The lights; I picked up a set of bull rings and made a little bracket to fit down inside. Had to trim the plastic on the ring a bit. Rings still function. I re-did the mount on the light as well so I can rotate/pivot where I need it. Looks like I need to repaint them as well
0425140837 by floggersg, on Flickr
Also here's where I mounted my little fuse block. Ill clean up the wires once I get everything installed and set.
0425140839b by floggersg, on Flickr
Last edited by Krookz; 04-25-2014 at 10:23 AM.
#44
Senior Member
Thread Starter
I really hate that you cant edit your posts on this site!!!! Not sure what happened with the pics so there it is again.
Hope this helps...
Yea... figured id pull it off before I destroy it in the woods. Still need to get those skid plates done. So much stuff to do!
The lights; I picked up a set of bull rings and made a little bracket to fit down inside. Had to trim the plastic on the ring a bit. Rings still function. I re-did the mount on the light as well so I can rotate/pivot where I need it. Looks like I need to repaint them as well
Also here's where I mounted my little fuse block. Ill clean up the wires once I get everything installed and set.
Hope this helps...
Yea... figured id pull it off before I destroy it in the woods. Still need to get those skid plates done. So much stuff to do!
The lights; I picked up a set of bull rings and made a little bracket to fit down inside. Had to trim the plastic on the ring a bit. Rings still function. I re-did the mount on the light as well so I can rotate/pivot where I need it. Looks like I need to repaint them as well
Also here's where I mounted my little fuse block. Ill clean up the wires once I get everything installed and set.
The following users liked this post:
R4ZORBL4DE (05-02-2014)
#46
Unique & Different
Good looking and sexy truck. Love the flex pictures.
#47
Senior Member
Thread Starter
The following users liked this post:
R4ZORBL4DE (05-02-2014)