Build Thread for my Ruby-Red, Coyote powered, 2013 FX2 Sport
 

Hello everyone,
I just joined here & submitted my Introduction Thread (see Link below):
https://www.f150forum.com/f3/new-member-here-nc-400084/

Now its time to get you all caught up on my BUILD, that never seems to be done...lol

This is my Ruby-Red 2013 F150 FX2 Sport "as purchased" in May 2016 (except for Toolbox which I transferred):

https://cimg2.ibsrv.net/gimg/www.for...19f6559de5.jpg
https://cimg4.ibsrv.net/gimg/www.for...6c062d534e.jpg
https://cimg5.ibsrv.net/gimg/www.for...b2a220f356.jpg

Window's Tinted & Ventshades installed:

https://cimg6.ibsrv.net/gimg/www.for...77897701c9.jpg

My Emblems were completely covered in Plasti-Dip, when I bought it & IMO looked like huge black blobs, so
I carefully removed the Plasti-Dip from the trim & script only, essentially changing the blue to black.
I think they came out nice :thumbsup:

https://cimg9.ibsrv.net/gimg/www.for...ac900aac71.jpg

Husky brand, X-Act Contour Floor Mat's (rear is a 1 piece):


https://cimg8.ibsrv.net/gimg/www.for...3d82e325f5.jpg

Installed a K&N Filter & these Sylvania ZXE's, there was a difference for sure, even though its harder to tell in the pic :

https://cimg6.ibsrv.net/gimg/www.for...ae024ec49b.jpg
https://cimg8.ibsrv.net/gimg/www.for...9b60176d64.jpg

Bought a Ford-Performance, Shackle Kit (see link below) from Summit-Racing
https://performanceparts.ford.com/part/M-3000-G
Which dropped the Rear by 2 inches & IMO created a perfect stance, only 1/2 inch higher in the rear now :thumbup:

https://cimg2.ibsrv.net/gimg/www.for...a7cc482cfb.jpg
https://cimg3.ibsrv.net/gimg/www.for...b52386ebe0.jpg

Spray in Bed-Liner, done :thumbsup:

https://cimg0.ibsrv.net/gimg/www.for...7175fa0c6b.jpg

Scrapped the OE 3rd Brake Light, for a Smoked LED https://www.ford-trucks.com/forums/i...coolgleamA.gif

https://cimg2.ibsrv.net/gimg/www.for...fb992490aa.jpg

OEM vs Smoke LED


https://cimg3.ibsrv.net/gimg/www.for...f3fa273310.jpg

Cargo Light & Brake Light (LED's) activated

* Plug n Play installation, bought from K2MOTOR on eBay *

Installed a complete Cat-Back, Legato Stainless Dual Exhaust System https://www.ford-trucks.com/forums/i.../party0031.gif
Took me nearly 2.5 hours, start to finish, in my driveway. She has a quiet rumble while idling, but damn u know there is a V8 under the hood after u put your foot on the throttle. It sounds great, a nice V8 rumble, with NO stupid cracking sounds & no drone while cruising https://www.ford-trucks.com/forums/i...ilgrin0007.gif
BTW...The cost was unbelievable https://www.ford-trucks.com/forums/i.../party0005.gif
https://legatoperformance.com/produc...t-cat-back-kit


https://cimg8.ibsrv.net/gimg/www.for...e11e6065fe.jpg

Installed a GlowShift VoltMeter & put that dumb a** coin-holder in the trash, where it belongs https://www.ford-trucks.com/forums/i.../party0005.gif

https://cimg8.ibsrv.net/gimg/www.for...83fab39a86.jpg