Yes, I saw the other How-To. I just had this laying around so if it's not wanted/needed please delete--no worries.







Since I'm home for the week I decided to clear up the headlights on my mother's 2001 Toyota Camry. I know a lot of us have newer vehicles and don't have to worry about this (yet), but many of you own several vehicles. This should help if your headlights have that nasty, yellow, "cloudy" look, as such:






Before I start I'll just say that if your stock of detailing supplies is low don't worry. You can do this with a limited number of supplies. All you really need you can buy at Wal-Mart. The bare-bone essentials are: some rags, 1000/2000 grit sandpaper, and polish (Meg's Ultimate Compound @ Wal-Mart). I will list everything I used, though. Some of it probably wasn't necessary, but I did it anyway.

The entire process would have taken me 20 minutes tops had I not stopped to take pictures several times. The headlights aren't big at all so it doesn't take long to get them looking great again.




(again, this is what I used)
Materials:
1. Bowl or bucket filled with soapy water
2. Some old rags (type doesn't matter)
3. 1000 grit sandpaper
4. 2000 grit sandpaper
5. Masking tape (I used blue painter's)
6. DA polisher
7. M105 + heavy cut pad
8. M205 + light cut pad
9. Plast-X + foam hand pad
10. Latex Gloves







(I did one headlight at a time to get some before/after shots. Feel free to do both at once.)
My Steps:
1. Put the sandpaper into the soapy dish to soak for a few minutes while you prep everything else.





2. Use the masking tape and tape off areas you don't want to accidentally wet-sand or have polish get into.





3. Wet sand with 1000 grit first. Work in straight lines, first horizontally then vertically. How much you need to sand depends on how bad of shape your headlights are in, but it's mostly a feel thing. Just do what you think is enough.





4. Now wet sand with 2000 grit using the same method as the 1000 grit.
5. Wipe off all the water with a rag.
6. Use the M105 with a heavy-cut pad. You shouldn't really worry about screwing anything up since headlights are far less prone to damage than paint. Put a few drops of M105 on the pad.





7. Spread it around by hand first to prevent slinging the polish everywhere. After spreading it around by hand use a low-speed setting (2 on the PC) to spread it evenly.





8. Turn the polisher up (5 on the PC) and go to town. Work it around evenly and slowly. No need to go fast as there isn't much ground to cover. After working it for a minute or so go ahead and wipe it off to take a look.
9. If it looks pretty clear (mine did after the M105 alone) use the M205 the exact same way as the M105. This time use the light-cut pad. If it still looks pretty foggy from the wet sanding then do another pass or two.
10. Wipe off the M205 and put a small drop of Plast-X on the foam hand pad to work in by hand. Spread it around and rub it in.





11. Follow steps 1-10 again for the next headlight.

 

Here are a few comparison shots after the first headlight was finished (I did the passenger side first, obviously):








Before and Afters:









Final thoughts:
I feel I could have gotten away with using just 2000 grit and M105. If you're short on stock or cheap feel free to try it this way and report back to us. After I used the M105 the headlight was pretty clear. I just used the extra stuff because I had already taken the time to pack it up and take it home in the first place.

You can do this by hand and without the M105/205, though. Go pick up some Meg's Ultimate Rubbing Compound from Wal-Mart. With the foam hand pads you should be able to get out the 2000 grit marks no problem! It's easy to do by hand because it's such a small area to work. Hopefully this helps some people--I know my mother appreciated the early Christmas gift.

 

good work on the headlights they look better than new

 

Thanx. That's great and I have all of those supplies laying around in the garage.

 

i should have checked this out sooner.pretty amazing the work you did.thanks for the how to thread i need to try this myself on my wifes mini van.

 

I bought a $9 turtle wax kit from walmart and I'm super happy with the results on my wife's car:



only took me 30 minutes, didn't even use an electric buffer, just hand buffed.

 

Damn for a hand job(lol) that aint bad.

 

Oh do I love hand jobs lol, I usually use 1200 grit, then maybe 1800. then I use rubbing compound and buffer, then polish and the polish pad. Idk though, my ferd headlights seem to yellow up pretty quickly though, maybe I should sand a lil longer?

 

awesome thread man. def gonna have to do this soon since i got my HIDs in!

 

If it clears up and looks good after doing it, but turns yellow again shortly after, you could try putting a few light coats of clear on the headlights. Do this after the "cleaning" process. I ended up putting a light touch of clear on the Camry's headlights and they are still looking clear.