Honeywell Garrett 2015+ Ford F-150 3.5L & 2.7L EcoBoost Intercooler C.A.R.B. Approved
09-04-2018, 01:20 PM
#1
F150 Forum
Thread Starter
Garrett Motion 2015+ Ford F-150 3.5L & 2.7L EcoBoost Intercooler C.A.R.B. Approved
Just Released the New Garrett Motion 2015+ Ford F-150 3.5L & 2.7L EcoBoost Intercooler Drop-in Upgrade
The Garrett® direct fit F150 charge air cooler boasts an 83% larger core than stock to provide an estimated 25 degree Fahrenheit reduction in air temperature and a 30% reduction in pressure drop. Optimized end tanks improve air flow through the core by improving turbulent design features found in the stock unit. This direct fit performance intercooler is easily installed and can support up to 750 horsepower all while reusing the stock bolts, hoses, and clamps.
Visit our website to learn more here:
https://www.turbobygarrett.com/turbo...st-intercooler
Click here to purchase directly:
http://bit.ly/f150-intercooler-forum
3.5L / 2.7L Ford F150 Direct Fit Performance Charge Air Cooler
2015+ Ford F150
2.7L / 3.5L Ecoboost engine platform
PN: 870702-6001
C.A.R.B. EO# D-794
Supports up to 750 Horsepower
Drain plug to relieve condensation
*Not engineered to fit any other applications
Available Sept 4, 2018
Construction:
Pressure tested for quality and reliability
C.A.R.B. Approved:
Granted by the California Air Resource Board (C.A.R.B), executive order #D-794 allows the 870702-6001 direct fit performance charge air cooler to be used on specific emission controlled vehicles.
California is the only state that is permitted to issue emissions standards with an approval form the Environmental Protection Agency.
Obtaining a C.A.R.B certification identifies this intercooler will not increase vehicle emissions.
https://arb.ca.gov/msprog/aftermkt/devices/eo/D-794.pdf
Approved by the EPA and C.A.R.B.
Performance: Dyno Testing
Back to Back Dyno Pulls
Dyno Graphs
+ 16 horsepower increase over OE at full heat saturation.
Up to + 16 horsepower increase over OE at full heat saturation.
Installation:
1.5 Hour Installation Time
Drain Plug Feature
The Garrett direct fit performance charge air cooler comes with a fully machined drain plug to relieve condensation buildup commonly found in the F150 platform. The bolt can be removed with a 3/8 open ended wrench.
Installers can test for condensation by turning the engine on, transmission in park, remove the bolt and place a catch can under the opening. Observe for any fluids. If fluid is present, gently rev the engine several times to dispel. Be sure to dispose of fluid with your local waste management facility.
Drain Plug Feature
The Garrett® direct fit F150 charge air cooler boasts an 83% larger core than stock to provide an estimated 25 degree Fahrenheit reduction in air temperature and a 30% reduction in pressure drop. Optimized end tanks improve air flow through the core by improving turbulent design features found in the stock unit. This direct fit performance intercooler is easily installed and can support up to 750 horsepower all while reusing the stock bolts, hoses, and clamps.
Visit our website to learn more here:
https://www.turbobygarrett.com/turbo...st-intercooler
Click here to purchase directly:
http://bit.ly/f150-intercooler-forum
3.5L / 2.7L Ford F150 Direct Fit Performance Charge Air Cooler
2015+ Ford F150
2.7L / 3.5L Ecoboost engine platform
PN: 870702-6001
C.A.R.B. EO# D-794
Supports up to 750 Horsepower
Drain plug to relieve condensation
*Not engineered to fit any other applications
Available Sept 4, 2018
Construction:
- Cast aluminum end tanks
- Advanced offset fin design
- TIG welded for improved strength
- Vacuum brazed bar-and-plate design
- 83% larger aluminum intercooler core
- Up to 25 degree reduction in charge air temp
Pressure tested for quality and reliability
C.A.R.B. Approved:
Granted by the California Air Resource Board (C.A.R.B), executive order #D-794 allows the 870702-6001 direct fit performance charge air cooler to be used on specific emission controlled vehicles.
California is the only state that is permitted to issue emissions standards with an approval form the Environmental Protection Agency.
Obtaining a C.A.R.B certification identifies this intercooler will not increase vehicle emissions.
https://arb.ca.gov/msprog/aftermkt/devices/eo/D-794.pdf
Approved by the EPA and C.A.R.B.
Performance: Dyno Testing
Back to Back Dyno Pulls
Dyno Graphs
+ 16 horsepower increase over OE at full heat saturation.
Up to + 16 horsepower increase over OE at full heat saturation.
Installation:
- This direct fit performance charge air cooler installs in one and a half hours using basic hand tools
- Reuses the factory hoses, clamps, bolts
- Can be installed without removing the front bumper
- Intercooler comes with a new screw for the blow off valve bracket
1.5 Hour Installation Time
Drain Plug Feature
The Garrett direct fit performance charge air cooler comes with a fully machined drain plug to relieve condensation buildup commonly found in the F150 platform. The bolt can be removed with a 3/8 open ended wrench.
Installers can test for condensation by turning the engine on, transmission in park, remove the bolt and place a catch can under the opening. Observe for any fluids. If fluid is present, gently rev the engine several times to dispel. Be sure to dispose of fluid with your local waste management facility.
Drain Plug Feature
Last edited by Garrett Motion; 10-01-2018 at 01:20 PM.
The following users liked this post:
1NiceHarley (09-04-2018)
02-23-2019, 01:46 PM
#2
