LED cubes in Foglight
#21
Project White Fang
Thread Starter
Here are some on Amazon
Amazon.com: 3x3 6KLED 18W WHITE CREE LED LIGHT Spot Beam FREE BLACK COVER ATV/UTV Street Tractor Cube Square - Offroad Used MARINE FISHING BOATJEEP TRUCK SUV (Pack of 2): Automotive
The white ones usually denote "marine" which is typically for boating. You may have better luck adding marine into the search bar like I did.
I did this mod and just popped buckets out of bumper, there are only 3 bolts holding it in. Two up top and one on bottom of bracket.
Then just measured how deep I wanted them, drilled a hole for bolts bracket. I used a large washer on the underside of the bucket to give it some strength. Then I just wired them into stock fig light wires and used stock switch.
Amazon.com: 3x3 6KLED 18W WHITE CREE LED LIGHT Spot Beam FREE BLACK COVER ATV/UTV Street Tractor Cube Square - Offroad Used MARINE FISHING BOATJEEP TRUCK SUV (Pack of 2): Automotive
The white ones usually denote "marine" which is typically for boating. You may have better luck adding marine into the search bar like I did.
I did this mod and just popped buckets out of bumper, there are only 3 bolts holding it in. Two up top and one on bottom of bracket.
Then just measured how deep I wanted them, drilled a hole for bolts bracket. I used a large washer on the underside of the bucket to give it some strength. Then I just wired them into stock fig light wires and used stock switch.
#22
Project White Fang
Thread Starter
The bottom ones would be the best fit for the fogs. I'm pretty certain The white flush mount lights won't fit.
These white cubes should work for you. http://www.dominationlighting.com/product/white-d3-pods
Not sure if they ship to canada tho.
These white cubes should work for you. http://www.dominationlighting.com/product/white-d3-pods
Not sure if they ship to canada tho.
#23
Project White Fang
Thread Starter
If you're going with a fog light that shines evenly in all directions you don't need to drill a new hole. Once you get the factory lights out you'll see a tab with a hole in it on the inside of the housing. I used that for fogs before I switched locations. There's also a good writeup in the how to section using a strip of metal which works great.
p.s. yours look good
#24
Project White Fang
Thread Starter
So I ran into a headlight issue so I was holding back before I did ordering on these incase I needed to spend money on my headlights. Anyway now I'm ready to pull the trigger on the cubes so to be 100% before I do, this is the wiring I will need for the plug and play from the cubes to my existing foglight wires?
http://www.ebay.com/itm/321143908468?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
http://www.ebay.com/itm/321143908468?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
#25
Senior Member
So I ran into a headlight issue so I was holding back before I did ordering on these incase I needed to spend money on my headlights. Anyway now I'm ready to pull the trigger on the cubes so to be 100% before I do, this is the wiring I will need for the plug and play from the cubes to my existing foglight wires?
http://www.ebay.com/itm/321143908468?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
http://www.ebay.com/itm/321143908468?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Here's the harness you need to connect the cubes to your original fog harness.
http://www.stage3motorsports.com/501...-Adapters.html
#26
Project White Fang
Thread Starter
Originally Posted by llangarica
From my experience you shouldn't need any type of load resistor or anything like that to use replace your fogs with leds. You only need those when replacing your turn signals to led to prevent hyper flash. The fogs should be plug and play. You may want to invest in a relay harness for them, Not 100% needed but I installed one for added security.
Here's the harness you need to connect the cubes to your original fog harness.
http://www.stage3motorsports.com/501...-Adapters.html
Here's the harness you need to connect the cubes to your original fog harness.
http://www.stage3motorsports.com/501...-Adapters.html
#27
Project White Fang
Thread Starter
The ones I ordered on eBay, same as the amazon ones but $20 cheaper. Got them for $55 and faster shipping. Thanks for the help everyone!
http://www.ebay.com/itm/351213729442?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
http://www.ebay.com/itm/351213729442?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
#30
Senior Member
Well guys don't bite my head off now ,,but Ill tell you this ,,, you get what you pay for , IMO , if your not going rigid your wasting your time and money ,,, rigid or bust ,,, went the cheap way to , but it came back and bit me in the butt ,, spent $80 on a ebay set of wanna bees and after a few months i ended up spending $300 on rigids , now when i switch on my fogs ,,, I can see,,,, go Rigid or go home ,,
The following users liked this post:
MCDavis (10-18-2015)