Help with 2010 Factory F150 Remote Start
#11
Mine does the same thing, From what I understand you order it with the truck and the dealer installs the unit when the truck comes in, I had a local installer hard wire my radar detector on friday and he does remote starts and he thought that the Ford remote start was a nice set up it just plugs into the harness. My wifes Buick remote will continue to run, allow you to insert your key and just turn it to on. I guess a minor inconvience.
#12
Senior Member
Join Date: Dec 2009
Location: Rural SW Oklahoma
Posts: 213
Likes: 0
Received 0 Likes
on
0 Posts
My dealer installed Ford Bi-Directional remote start keeps running when you unlock the doors, get in and insert the key. It will stay running about 10-15 minutes w/o inserting the key.
#14
Senior Member
I have the ford remote start as well and when i picked up my truck it also shut off when i opened the door. Took it back to the dealer and they had to disable MyKey in order to keep your truck running when u open the door. I do not know the process on how to disable MyKey but that is what u need to have done, take it back to the dealer and tell them to disable MyKey they should know how to do that if they dont find a new dealer.
#15
its not mykey that you disable. it is the safety shut down for my key.your my key works either way.
the way it works is there is a chip in the key, so when you turn on my key give it to your kid and he starts it it reads the chip but if it is remote started ford or aftermarket it wont read the chip and the safty control wont work
the way it works is there is a chip in the key, so when you turn on my key give it to your kid and he starts it it reads the chip but if it is remote started ford or aftermarket it wont read the chip and the safty control wont work
#16
Hey, TeamRoper Can you get ahold of your dealer that did that for you and get them to print off some instructions on how to program the vehicle not to shut down when doors are opened and to run for 15min.
Then post those instructions here or I will give you an address to mail then too.
Half these dealers around my area don't have a clue on how to do this!!
Then post those instructions here or I will give you an address to mail then too.
Half these dealers around my area don't have a clue on how to do this!!
#17
Senior Member
Hey, TeamRoper Can you get ahold of your dealer that did that for you and get them to print off some instructions on how to program the vehicle not to shut down when doors are opened and to run for 15min.
Then post those instructions here or I will give you an address to mail then too.
Half these dealers around my area don't have a clue on how to do this!!
Then post those instructions here or I will give you an address to mail then too.
Half these dealers around my area don't have a clue on how to do this!!
#18
I didn't know that that font was so "disturbing"
I know dealers are not allowed to do this anymore but I know that every dealer is NOT "buy the book"
Everyone know's that there are dealers out there that still perform this even though Ford says they are not suppose to!!!!
#20
SYSTEM PROGRAMING
you will need to find the programing button .under dash driver side little black button
in a black cap.
**must be done in this order.
1 turn dome light on.
2 press and hold brake
2a turn ignition on
3 press and hold program button you will hear 3 honks.
4 release program button and brake.
5 now you can program more remotes by pressing the remote.
6*** press program button it will** honk 4 times.
**** now your in programing mode**** press the brake to advance to the disired option********
the horn will honk to tell you the option so 5 honks option 5.
to change the option press your remote.there is a led under the dash led on program on led off program off**
1 learn tach wont need this program for 04 and up
2 door ajar swith inverter led on positive
3 key in sense led on positive
4 extended horn honk led off standard honk.
press program button 5 honks.
1 tachless mode led on tachless all 04 and up led off for older trucks
2 tachless timing led on is 8 second crank 04 and up led off 1 second
3 run time led off 10min. *****LED ON 15 MIN>>>*****
4 press and hold start led on press led off double press
5 diesel timer led off
6 horn honk on start led on honk
7 *******i cant tell you hint led on my##$$$ on led off my@@$$%$ off
so push brake to go to options
and push remote to chage it.
****this is for the remote start only not the alarm remote start.****
turn key off and test
you will need to find the programing button .under dash driver side little black button
in a black cap.
**must be done in this order.
1 turn dome light on.
2 press and hold brake
2a turn ignition on
3 press and hold program button you will hear 3 honks.
4 release program button and brake.
5 now you can program more remotes by pressing the remote.
6*** press program button it will** honk 4 times.
**** now your in programing mode**** press the brake to advance to the disired option********
the horn will honk to tell you the option so 5 honks option 5.
to change the option press your remote.there is a led under the dash led on program on led off program off**
1 learn tach wont need this program for 04 and up
2 door ajar swith inverter led on positive
3 key in sense led on positive
4 extended horn honk led off standard honk.
press program button 5 honks.
1 tachless mode led on tachless all 04 and up led off for older trucks
2 tachless timing led on is 8 second crank 04 and up led off 1 second
3 run time led off 10min. *****LED ON 15 MIN>>>*****
4 press and hold start led on press led off double press
5 diesel timer led off
6 horn honk on start led on honk
7 *******i cant tell you hint led on my##$$$ on led off my@@$$%$ off
so push brake to go to options
and push remote to chage it.
****this is for the remote start only not the alarm remote start.****
turn key off and test
Last edited by badcat; 02-07-2010 at 05:24 PM.