Forscan applications
#3031
Senior Member
This depends on how bad you really want this option....If the wire is truly missing then you would most likely need to replace the entire main harness with one that is equipped with it to add that feature, that is a $250.00ish harness & around 6-8 hrs of labor to make the swap.
Simple code change
726-12-01
xxx1 xxxC xx Auto headlamps enabled
xxx0 xxxF xx auto headlamps disabled
The following users liked this post:
2slow05 (11-19-2017)
#3033
Senior Member
You don't need to replace the entire harness, you just need to run those specific wires. I know you need one to go to the switch and one to the BCM. I don't know if there are more or not, but that shouldn't cost you more than a $30 roll of wire.
Simple code change
726-12-01
xxx1 xxxC xx Auto headlamps enabled
xxx0 xxxF xx auto headlamps disabled
Simple code change
726-12-01
xxx1 xxxC xx Auto headlamps enabled
xxx0 xxxF xx auto headlamps disabled
Yeah I figured it was just a matter of the pigtail there, possibly buy the sensor and switch then activate it in forscan. I saw the hex codes in the document that forscan can make changes. It would be nice if you could buy the pigtail and put it together with just a few connectors going together.
#3034
Senior Member
Yeah I figured it was just a matter of the pigtail there, possibly buy the sensor and switch then activate it in forscan. I saw the hex codes in the document that forscan can make changes. It would be nice if you could buy the pigtail and put it together with just a few connectors going together.
It has the pigtail part number and the instructions on where to run the wires. One goes to the BCM, one to the climate control and one to the headlight switch. Then run one wire from the head light switch to a harness in the steering wheel.
#3035
Has anyone successfully removed the 3 Sirius menus from sync 2 system?
I would like to go straight to CD/USB from radio.
I have read the spread sheet but it seems to be for 2014 and newer. Is this correct?.
2012 FX4, All options
Many thanks.
I would like to go straight to CD/USB from radio.
I have read the spread sheet but it seems to be for 2014 and newer. Is this correct?.
2012 FX4, All options
Many thanks.
#3036
Senior Member
*xxx xxxx xxxx Remove sirius. decrease * by 2 values. If A make it an 8, if 2 then make it 0 and so on.
The spreadsheet in my signature is technically for 2011-2014 but I can only test on a 2014 limited. So I only can tell you they work for that unless others confirm for other years.
The following users liked this post:
CHICKS (11-22-2017)
#3037
How's she goin' eh?
What about if it's a 0? I have 0804 4000 0025
#3038
Senior Member
#3039
How's she goin' eh?
There's a post of the list of values. I forget where.
#3040
It's my first day
Front camera's are on my radar as of late; so too are adding rear park aid sensors to my 2014 XL which seems pretty easy, although I will need to do some research with the as built compare utility to locate the BCM enable bit for the PAM. As far as I'm aware nobody on the internet has done either of these things yet to their 12 Gen F150 which is perfect considering I am going to try and do it to an XL wit the luxurious 101a package lol.
This video is very interesting for three reasons:
1. Front Camera.
2. Video at any speed on My Ford Touch.
3. Potentially an aux video input.
Theoretically if you enable the front camera at any speed you could intercept the signal with an RCA tap and run a PlayStation or whatever you want to your My Ford Touch screen.
Page 8 of the attached 2014 BCM wiring diagram shows that everything for the raptor front camera and off road switch goes to the BCM, but I'm not sure if you'd need a special raptor only firmware on the IPC or FCIM for this considering the electronic diff switch is part of the soft-enable process.
If you are only interested in adding rear park aids to your F150, I attached my other wiring diagrams for that too. It's primarily what I'm focused on but I'll add a front camera while I'm at it if it's not too much extra work.
If you want to add My Ford Touch or Sync 3 to your 2011 and up F150 that is another topic and here is a great piece of equipment that you'll most certainly want to help you get started. You will need Harness B and still need to modify it a bit.
https://www.4dtech.com/4-to-8-pnp-co...-for-sync-2-3/
This video is very interesting for three reasons:
1. Front Camera.
2. Video at any speed on My Ford Touch.
3. Potentially an aux video input.
Theoretically if you enable the front camera at any speed you could intercept the signal with an RCA tap and run a PlayStation or whatever you want to your My Ford Touch screen.
Page 8 of the attached 2014 BCM wiring diagram shows that everything for the raptor front camera and off road switch goes to the BCM, but I'm not sure if you'd need a special raptor only firmware on the IPC or FCIM for this considering the electronic diff switch is part of the soft-enable process.
If you are only interested in adding rear park aids to your F150, I attached my other wiring diagrams for that too. It's primarily what I'm focused on but I'll add a front camera while I'm at it if it's not too much extra work.
If you want to add My Ford Touch or Sync 3 to your 2011 and up F150 that is another topic and here is a great piece of equipment that you'll most certainly want to help you get started. You will need Harness B and still need to modify it a bit.
https://www.4dtech.com/4-to-8-pnp-co...-for-sync-2-3/
Last edited by Airborne_Ape; 11-22-2017 at 03:53 AM.