Forscan applications
#3111
Are you able to do this within forscan? I have switchback led's for my turn signal and they are pretty bright at night.
#3112
911 Issue work around.
I removed the Nav in motion block from sync and noticed I lost the option to call 911 if there is a crash, I left it like that for a day or so. Today I noticed the cross is back and I have an option to create 2 emergency contacts for sync to call. So, I added a new contact in my phone called cops and put 911 for its phone number and used that as the emergency contact #1 for sync to call if there is a crash. If anyone wants to do this its in the "phone" section of sync.
The following users liked this post:
jp360cj (01-04-2018)
#3113
Senior Member
#3114
Turn signals should only come on when the turn signal is activated. For the running lights, the front and rear are most likely wired to the same circuit, so if you could kill the power the front, you wouldn't have any taillights. If you can find a wiring diagram, you should be able to confirm. It could, however, be done with a relay and some wiring, but I doubt it would be worth the trouble.
Well that’s not the case. The turn signals are on when the headlights come on.
#3115
Senior Member
Edit: if your turn signals come on with the headlights, then what happens when you activate the turn signal?
Last edited by jp360cj; 01-04-2018 at 10:07 AM.
#3116
I recently used Forscan to activate the backup camera and the factory brake controller. It worked perfectly. This morning I tried to connect Forscan to disable the car finder feature (installing remote start) and I keep getting the error ... Unable to connect to vehicle. Please make sure the ignition key is ON and try again.
This is odd since I'm using the exact laptop and ELM327 adapter that I used to activate the camera and brake controller. Any ideas on how to fix this? Everything is connected and ignition is ON.
This is odd since I'm using the exact laptop and ELM327 adapter that I used to activate the camera and brake controller. Any ideas on how to fix this? Everything is connected and ignition is ON.
#3117
Sounds to me like an issue with the aftermarket bulb. The turn signal portion of the bulb does not get power with the headlights. Turn signal is only powered when the switch is activated (unless you have turn signals set as DRL).
Edit: if your turn signals come on with the headlights, then what happens when you activate the turn signal?
Edit: if your turn signals come on with the headlights, then what happens when you activate the turn signal?
#3118
Senior Member
I recently used Forscan to activate the backup camera and the factory brake controller. It worked perfectly. This morning I tried to connect Forscan to disable the car finder feature (installing remote start) and I keep getting the error ... Unable to connect to vehicle. Please make sure the ignition key is ON and try again.
This is odd since I'm using the exact laptop and ELM327 adapter that I used to activate the camera and brake controller. Any ideas on how to fix this? Everything is connected and ignition is ON.
This is odd since I'm using the exact laptop and ELM327 adapter that I used to activate the camera and brake controller. Any ideas on how to fix this? Everything is connected and ignition is ON.
They are switchback LEDs that I have for the turn signal bulbs. When the headlights come on and the turn singles come on with the headlights it's glowing white. When the turn signals are activated it turns amber. I believe that's how all 2013/2014 F150's operate. I do have the OEM HID's so I'm not sure if that make a difference in how it works.
#3119
Senior Member
Good thread here:
https://www.f150forum.com/f118/forsc...8987/index986/
Basically, you know how you put your blinker on (actually click it, not tap) and take a corner and when the wheel goes straight again, the blinker stops? Yeah not when OUC is set to true. It means on until cancelled, so once that wheel turns straight, the blinker will still be on, until you tap it like you would normally cancel a blinker. That's my understanding of it.
Basically no point to it. But you can change the number of flashes from 3 to 5 (maybe other options) when you simply tap it while changing lanes and not making it so it stays on all the time until cancelled
https://www.f150forum.com/f118/forsc...8987/index986/
Basically, you know how you put your blinker on (actually click it, not tap) and take a corner and when the wheel goes straight again, the blinker stops? Yeah not when OUC is set to true. It means on until cancelled, so once that wheel turns straight, the blinker will still be on, until you tap it like you would normally cancel a blinker. That's my understanding of it.
Basically no point to it. But you can change the number of flashes from 3 to 5 (maybe other options) when you simply tap it while changing lanes and not making it so it stays on all the time until cancelled
#3120
Senior Member
They are switchback LEDs that I have for the turn signal bulbs. When the headlights come on and the turn singles come on with the headlights it's glowing white. When the turn signals are activated it turns amber. I believe that's how all 2013/2014 F150's operate. I do have the OEM HID's so I'm not sure if that make a difference in how it works.