Finished my led mod
#1
mortarman120
Thread Starter
Tell me what you u guys think. I think it goes good with what I have going with my truck so far I am happy they are not all crazy bright just wanted something to give the interior a good look
#4
Nice . I like it.
#5
Did you hard wire direct or put them on a switch. Did you use LED strips. Can you post pics of where exactly you mounted them. This is a project I will be working on very soon. Nice Job!
The following users liked this post:
Highsticks Eh! (08-22-2012)
#7
mortarman120
Thread Starter
Yes I will do a write up I took pictures as I was going so. I removed the coin hold and the cable for the 4x4 is there on 2wds soo I tapped into that constant 12v and goes off with the truck going off
Trending Topics
#9
mortarman120
Thread Starter
First thing u want to do is remove the coin holder notice only for 2WDS ONLY
After u pull the coin holder out you will we the cable grab and look for the black wire which is ur ground and the purple with redish brown stripe on it that one is the constant 12v
.
Then you can remove the plastic pieces on the very front sides of the center console remove driver and passenger one so u can send the led through to the other side
The u can go ahead and run the LEDs through the hole. Ok for the. Back led run the wire Inbetween ur seat and center console. Ok so ur led is under u seat what u can do with the excess wire is just use a flat tip and tuck it under the center console and instead of using the screws to attach the led I went the easy route and used 3mm double sided tape here is where u can attach it it's the little plastic piece that is on the edge of ur seat cover to attach it to the frame
Ok now for the front pretty easy for the passenger side I just again attached using 3mm double sided tape there is a little spot in between the glove box and ac box u will see it when u look that is where I put for the excess wire I stuffed it all in behind the plastic trim piece that was removed in the beginning
For the driver side same thing stuffed all the extra wire behind the plastic trim was really many places to attach this led to so I again 3mm tape and hook it onto the wire harness under the steering wheel
Now that everything is ran I then hooked the wires up u have run the wires up the dash to the coin holder spot kinda tricky if u got big hands
Stuffed it all back in and put the coin holder back and let there be light
These LEDs have a control box for the setting I just want it on one thing so I just tucked the box away behind the plastic trim to
I got these LEDs at www.ledglows.com lots of colors, and sizes and priced very good I paid 43 dollars including shipping for my 4 piece set do not get the little fuse relay things for the kit as for they do not fit our truck our fuses are super Tiny they are like low pro mini ones and the 43 dollars was 6 dollars for the fuze relay soo my kit was only like 37 with shipping if u have any questions feel free to message
After u pull the coin holder out you will we the cable grab and look for the black wire which is ur ground and the purple with redish brown stripe on it that one is the constant 12v
.
Then you can remove the plastic pieces on the very front sides of the center console remove driver and passenger one so u can send the led through to the other side
The u can go ahead and run the LEDs through the hole. Ok for the. Back led run the wire Inbetween ur seat and center console. Ok so ur led is under u seat what u can do with the excess wire is just use a flat tip and tuck it under the center console and instead of using the screws to attach the led I went the easy route and used 3mm double sided tape here is where u can attach it it's the little plastic piece that is on the edge of ur seat cover to attach it to the frame
Ok now for the front pretty easy for the passenger side I just again attached using 3mm double sided tape there is a little spot in between the glove box and ac box u will see it when u look that is where I put for the excess wire I stuffed it all in behind the plastic trim piece that was removed in the beginning
For the driver side same thing stuffed all the extra wire behind the plastic trim was really many places to attach this led to so I again 3mm tape and hook it onto the wire harness under the steering wheel
Now that everything is ran I then hooked the wires up u have run the wires up the dash to the coin holder spot kinda tricky if u got big hands
Stuffed it all back in and put the coin holder back and let there be light
These LEDs have a control box for the setting I just want it on one thing so I just tucked the box away behind the plastic trim to
I got these LEDs at www.ledglows.com lots of colors, and sizes and priced very good I paid 43 dollars including shipping for my 4 piece set do not get the little fuse relay things for the kit as for they do not fit our truck our fuses are super Tiny they are like low pro mini ones and the 43 dollars was 6 dollars for the fuze relay soo my kit was only like 37 with shipping if u have any questions feel free to message
The following users liked this post:
tallguy804 (07-15-2012)