Add puddle lights to mirror harness
#1
Add puddle lights to mirror harness
First time contributing, I wanted to share my puddle light wiring in case someone else out there wants to do it the same way. I hate splicing into my factory harnesses on my truck especially since it's under warranty. So instead of splicing into the violet wire on the truck side of the harness and creating a headache to remove my mirrors in the future I decided to add a pin to my mirror harness connector. It took me longer than I'd like to admit to find the right part to do this so I wanted to share. The part for the wire pin crimp is Mouser Part #:
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/ProductDetail.aspx?R=2-1419158-5virtualkey57100000virtualkey571-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/ProductDetail.aspx?R=2-1419158-5virtualkey57100000virtualkey571-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
The following 3 users liked this post by Jfrerichs:
#2
One Clean Machine
iTrader: (5)
I just used door bell wire on the mirror side, for my puddle lamps. It was plenty stiff, and matted perfectly to the door side connector. I was sure to use electrical tape to secure the new wire to the existing wire, then I hotglued it into the mirror side connector!
Held up great so for for, 2 yrs.
Held up great so for for, 2 yrs.
#3
I just used door bell wire on the mirror side, for my puddle lamps. It was plenty stiff, and matted perfectly to the door side connector. I was sure to use electrical tape to secure the new wire to the existing wire, then I hotglued it into the mirror side connector!
Held up great so for for, 2 yrs.
Held up great so for for, 2 yrs.
#4
T
First time contributing, I wanted to share my puddle light wiring in case someone else out there wants to do it the same way. I hate splicing into my factory harnesses on my truck especially since it's under warranty. So instead of splicing into the violet wire on the truck side of the harness and creating a headache to remove my mirrors in the future I decided to add a pin to my mirror harness connector. It took me longer than I'd like to admit to find the right part to do this so I wanted to share. The part for the wire pin crimp is Mouser Part #:
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/ProductDetail.aspx?R=2-1419158-5virtualkey57100000virtualkey571-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/ProductDetail.aspx?R=2-1419158-5virtualkey57100000virtualkey571-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
https://www.arrow.com/en/products/2-1419158-5/te-connectivity?utm_source=FindChips&utm_medium=invLi sting&utm_campaign=FC2015
#5
Senior Member
I just used door bell wire on the mirror side, for my puddle lamps. It was plenty stiff, and matted perfectly to the door side connector. I was sure to use electrical tape to secure the new wire to the existing wire, then I hotglued it into the mirror side connector!
Held up great so for for, 2 yrs.
Held up great so for for, 2 yrs.
I added puddle lights and turn signals to my Tremor and found 2 mirror harnesses on ebay........pulled the mirror apart and installed the new harness/ signals/lights and worked out great.
#6
Back in a Ford
First time contributing, I wanted to share my puddle light wiring in case someone else out there wants to do it the same way. I hate splicing into my factory harnesses on my truck especially since it's under warranty. So instead of splicing into the violet wire on the truck side of the harness and creating a headache to remove my mirrors in the future I decided to add a pin to my mirror harness connector. It took me longer than I'd like to admit to find the right part to do this so I wanted to share. The part for the wire pin crimp is Mouser Part #:
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/Product...71-2-1419158-5
Jake
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/Product...71-2-1419158-5
Jake
I would like to add the wiring directly into the mirror harness the same way you did; no splicing of wires, and leaving all the wiring in the mirror-side connector. To that end, I have a set of wires ready to add to the connector to power the new LED puddle lamps, but need to know which pin position I need to add the pins to so I can get power and ground for the puddle lamps.
I believe pin 11 (on the mirror side connector) is power for the lamps, but is there a dedicated pin for ground for the puddle lamps? If so, which position in the connector needs to be populated for ground? Can you confirm pin 11 is indeed power?
Thanks in advance!
Trending Topics
#8
First time contributing, I wanted to share my puddle light wiring in case someone else out there wants to do it the same way. I hate splicing into my factory harnesses on my truck especially since it's under warranty. So instead of splicing into the violet wire on the truck side of the harness and creating a headache to remove my mirrors in the future I decided to add a pin to my mirror harness connector. It took me longer than I'd like to admit to find the right part to do this so I wanted to share. The part for the wire pin crimp is Mouser Part #:
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/Product...71-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
571-2-1419158-5 Manufacturer Part #: 2-1419158-5. http://www.mouser.com/Search/Product...71-2-1419158-5
My hardest part was actually finding the 20 gauge wire so make sure you have that on hand before your start because most stores will only have 18 gauge as the smallest unless you want to do speaker wire which I didn't because I wanted a more factory look. Once I'm don't the only way you would know the puddle lamps are not factory to the mirror would be to take it apart harness just looks like it was made for it.
I should be able to finish getting these wired up and installed tomorrow is my goal. While I have the mirror apart I and also adding the front facing turn signal mod.
Hope this helps someone.
Jake
where did you get the ground?
#10
Senior Member
That sounds like a 13th gen truck. Or even 14th.