2012/2013+ Platinum, Lariat Grille help
#1
Senior Member
Thread Starter
2012/2013+ Platinum, Lariat Grille help
Hey guys. I have a favor to ask. I am trying to figure out a better grille for my 2001 F350. Nothing on the aftermarket is tickling my fancy so I was brainstorming trying to cut the center section of a newer F150 grille to place it into the shell of my F350. The problem I am running into is measurements. So IF AT ALL POSSIBLE I would like to see if anyone with a 2013+ Lariat or Platinum, or even 2012 with the 6 bars, would be able to grab me a couple of measurements of their stock grill bars...just the middle bar sections, not the grille surround. I need a length and height of just the center bars...Thanks in advance for anyone willing to take a few minutes to help me out! These are the possible options I'm looking at:
Last edited by Buck; 01-26-2014 at 06:38 PM.
#2
Senior Member
I have a 2012 Lariat and just received my 6 bar billet grill which will replace whats in it now. I really like the 6 bar look and will install this week assuming I have time! It's a direct replacement so no cutting is required. I'll post up some pictures if you're interested after the install…………
#3
Senior Member
Thread Starter
can you take some height and width measurements of it for me as well? I am looking to Frankenstein a newer F150 grille into my 2001 Superduty grille shell. Thanks!
#4
One Clean Machine
iTrader: (5)
Buck its 44" wide by 12 & 3/4 tall! Thats on my 2012 FX4 6 bar grill! The other Styles, Lariat, Platinum will be the same measurements only cosmetic differences...
#5
noob :)
my platinum grill bars are about 11.5 inches top to bottom and ABOUT 42.5 inches long... the center bar is not as deep as the top and bottom ones so its a bit shorter
Last edited by byte; 01-26-2014 at 11:22 PM.
#6
noob :)
#7
Senior Member
Thread Starter
Thanks brotha! I gotta agree with Byte though...the different bar styles will probably have different width and depth measurements given the different spacing between them etc.
Trending Topics
#8
Senior Member
Thread Starter
Toddman are you measuring just the 6 bars or the entire inner section including the mesh on each side?
#9
One Clean Machine
iTrader: (5)
[QUOTE=Buck;3256975}
Toddman are you measuring just the 6 bars or the entire inner section including the mesh on each side?[/QUOTE]
Thats the entire Opening, the 6 bars only would be nearly 6" Shorter closer to 38" for just the 6-bars!
What I was Sayin in my Previous post, is the opening is the same for all Trims, only the different bars lengths Vary... Thought that was EZ to follow, guess not! Lol...
Toddman are you measuring just the 6 bars or the entire inner section including the mesh on each side?[/QUOTE]
Thats the entire Opening, the 6 bars only would be nearly 6" Shorter closer to 38" for just the 6-bars!
What I was Sayin in my Previous post, is the opening is the same for all Trims, only the different bars lengths Vary... Thought that was EZ to follow, guess not! Lol...
Last edited by Toddman38; 01-26-2014 at 08:53 PM.
#10
Senior Member
Thread Starter
Thats the entire Opening, the 6 bars only would be nearly 6" Shorter closer to 38" for just the 6-bars!
What I was Sayin in my Previous post, is the opening is the same for all Trims, only the different bars lengths Vary... Thought that was EZ to follow, guess not! Lol...
What I was Sayin in my Previous post, is the opening is the same for all Trims, only the different bars lengths Vary... Thought that was EZ to follow, guess not! Lol...
Thanks again
Last edited by Buck; 01-26-2014 at 10:42 PM.