Swap to Floor Console-16 XLT - Ford F150 Forum - Community of Ford Truck Fans

Topic Sponsor
Custom Fabrication Department This is the section to discuss any and all custom work that you've done or had made that may not be available on the retail market.

Swap to Floor Console-16 XLT

Reply

 
 
 
Old 07-31-2017, 10:39 PM
  #1  
Junior Member
Thread Starter
 
Join Date: Jun 2017
Posts: 3
Thanks: 0
Thanked 1 Time in 1 Post
Default Swap to Floor Console-16 XLT

I recently completed my swap from bench seat to floor console without issue. Thanks to this incredible site, it was pretty painless and only took an hour. The console I bought came with a wiring harness and both vent trim pieces. I had to purchase the two AC ducts (truck was pre-duct behind the radio which I cut the cap off to allow air flow) and the lower trim piece above the sliding cover. Overall very pleased and excited.

HOWEVER: I can not get power to the rear cigarette outlet and house plug as well as the inside cigarette outlet in console. I switched the double USB with the single USB from previous tray for SYNC purposes and have power to the cigarette outlet next to it. The wiring harness was connected to the plug coming out of the floor. Am I missing a fuse?


cbharding428 is offline  
Reply With Quote
The Following User Says Thank You to cbharding428 For This Useful Post:
4X4Pony (11-29-2017)
Old 08-26-2017, 04:40 AM
  #2  
Junior Member
 
Join Date: Aug 2017
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Default Possible fit in 2011

Would anyone here know if the full flow through console from a 2015 or later is at all compatible with a 2011?
Please keep in mind I'm not expecting direct bolt in swap. I would expect some degree of fabrication/customization to make it work. Would anyone be able to enlighten this quandary for me?
ma-fkn-ugh is offline  
Reply With Quote
Old 09-13-2017, 01:04 PM
  #3  
Junior Member
 
truck8lt's Avatar
 
Join Date: Jan 2015
Location: Orlando, Fl
Posts: 20
Thanked 2 Times in 2 Posts
Default

Originally Posted by ma-fkn-ugh View Post
Would anyone here know if the full flow through console from a 2015 or later is at all compatible with a 2011?
Please keep in mind I'm not expecting direct bolt in swap. I would expect some degree of fabrication/customization to make it work. Would anyone be able to enlighten this quandary for me?
why not buy the center console from an 09-13 and the associated trim panels and other parts needed. I did the swap on my 13, made a storage cubby for

where the shifter was, even hooked the rear vents up to the a/c.
truck8lt is offline  
Reply With Quote
The Following User Says Thank You to truck8lt For This Useful Post:
MrLunchbox (06-30-2018)
Old 09-27-2017, 07:36 AM
  #4  
Senior Member
 
covertness's Avatar
 
Join Date: May 2016
Posts: 375
Thanked 84 Times in 65 Posts
Default

I have a '16 flow through console I will be taking pictures of and putting on sale sometime over the weekend. Came out of a special edition Lariat and I swapped out my console cover, shift **** and boot with it. Black leather now with normal stitching.
covertness is offline  
Reply With Quote
Old 11-03-2017, 10:51 PM
  #5  
Member
 
mmickle13's Avatar
 
Join Date: Apr 2013
Location: weatherford tx
Posts: 56
Thanked 6 Times in 6 Posts
Default

Originally Posted by truck8lt View Post
why not buy the center console from an 09-13 and the associated trim panels and other parts needed. I did the swap on my 13, made a storage cubby for

where the shifter was, even hooked the rear vents up to the a/c.
Where did you buy the trim pieces at?
mmickle13 is offline  
Reply With Quote
Old 11-04-2017, 08:30 AM
  #6  
Junior Member
 
truck8lt's Avatar
 
Join Date: Jan 2015
Location: Orlando, Fl
Posts: 20
Thanked 2 Times in 2 Posts
Default

Through eBay, prices vary, usually around 178 for both (l&r) as a pair. If the floor kick trim wasn’t included w your console, you’ll need those 2 pieces too, around 48 each.
truck8lt is offline  
Reply With Quote
Old 11-14-2017, 04:32 PM
  #7  
Papermaker24
 
papermaker's Avatar
 
Join Date: Nov 2016
Location: Central Maine
Posts: 58
Thanked 3 Times in 3 Posts
Default

I would like to do the same project and was wondering the same thing 428.....
papermaker is offline  
Reply With Quote
Old 11-18-2017, 03:04 PM
  #8  
Member
 
Join Date: May 2013
Location: rancho cucamonga
Posts: 82
Thanked 25 Times in 14 Posts
Default

I did this center console swap with a shifter on mine its a single cab
parra is offline  
Reply With Quote
The Following User Says Thank You to parra For This Useful Post:
4X4Pony (11-29-2017)
Old 01-07-2018, 11:32 PM
  #9  
Senior Member
 
Commeeche's Avatar
 
Join Date: Sep 2013
Location: St Catherines, Ontario
Posts: 723
Thanked 78 Times in 71 Posts
Default

I did the swap on my 13. Went from the seat to the console. My dad liked it so much that he wants it done on his 16. Now to just find a console and pieces for it
Commeeche is offline  
Reply With Quote

Thread Tools
Search this Thread

Contact Us Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: