What did you do to your truck today?
#1791
Senior Member
I installed a Blackvue DR750S-2CH. You cannot see any part of the front camera when in the driver seat.
I ran the wiring along the headliner to behind the passenger rear seat. There, I will be installing the BlackVue B-124. I plan to hardwire this into the wiring leading to the inverter. It will tuck in nicely behind the jack. I will finish this off before work tomorrow.
#1792
Senior Member
What did you do to your truck today?
Did the easy headlight mod and swapped from chrome XLT grill to a chrome Lariat grill. Not a lot of change I know but I prefer the new grill. Maybe someone else needs the old one!
Old grill out! Well I say old, truck only has about 1200 miles on it!
Went ahead and did the easy headlight mod while I had the grill out. I know you don’t have to pull the headlights out to change the bulbs, but this far along and it’s very easy to do at this point. Swapped the low beam H11 for H9, swapped the high beam 9005 for 9011 and put the high beam 9005s in the fog lights.
New grill in and can’t wait to see the difference the new bulbs make. I did swap out 1 side and then turn them on for comparison (no photo unfortunately) but you can see a significant difference in the light output even in the day.
Old grill out! Well I say old, truck only has about 1200 miles on it!
Went ahead and did the easy headlight mod while I had the grill out. I know you don’t have to pull the headlights out to change the bulbs, but this far along and it’s very easy to do at this point. Swapped the low beam H11 for H9, swapped the high beam 9005 for 9011 and put the high beam 9005s in the fog lights.
New grill in and can’t wait to see the difference the new bulbs make. I did swap out 1 side and then turn them on for comparison (no photo unfortunately) but you can see a significant difference in the light output even in the day.
#1794
TOTM Sept. '18
iTrader: (1)
Finished the floor console and shift conversion today. It really seems like a different truck now. Many thanks to Firerunner and DeeMiniioon on their documentation in their thread.
While it was torn down I threw in some Dynamat.
Raptor carbon fiber shifter and sync 3 cubby door.
Mike
While it was torn down I threw in some Dynamat.
Raptor carbon fiber shifter and sync 3 cubby door.
Mike
The following 4 users liked this post by OCMike:
Firerunner (09-27-2018),
johnday in BFE (09-22-2018),
SPOAT (09-22-2018),
WildernessLVR (09-22-2018)
#1795
Senior Member
Wow, Mike that looks like a tremendous amount of work but the result is beautiful. I'll bet that sound deadening material makes a huge difference in noise reduction in the cab. Love that carbon fiber shifter too. Is that a Raptor take-off?
The following users liked this post:
OCMike (09-22-2018)
#1796
Finished the floor console and shift conversion today. It really seems like a different truck now. Many thanks to Firerunner and DeeMiniioon on their documentation in their thread.
While it was torn down I threw in some Dynamat.
Raptor carbon fiber shifter and sync 3 cubby door.
Mike
While it was torn down I threw in some Dynamat.
Raptor carbon fiber shifter and sync 3 cubby door.
Mike
The following users liked this post:
OCMike (09-22-2018)
#1797
TOTM Sept. '18
iTrader: (1)
Mike
The following users liked this post:
johnday in BFE (09-22-2018)
#1798
TOTM Sept. '18
iTrader: (1)
#1800
Senior Member
Slapped on some American Truck matte black door pillar vinyls.