Sync 3 Technical Discussion
11-14-2017, 03:39 PM
#11
The -AHH tarball only lists v2.2.16223... which is base version -LF and installs overlay -AKA
It seems I should have been pushed -AHG and my -SA base version would get the -AHF overlay.
I still have a few Tarballs to go thorugh...
11-14-2017, 04:29 PM
#12
If you just buy a new module that wouldn't be fun at all!
I'll throw this disclaimer out there up front that I'm a novice at linux/unix but I know enough (or how to google commands) to be dangerous.
It does use QNX6 as the main filesystem, however, my understanding is that the QNX boot/firmware/IFS partitions can be raw, and are written raw.
I believe 1 is raw despite showing FAT16, 4 is virtual, and 7 no clue. The remaining are QNX6
/dev/sdd1 * 32 65535 65504 32M 6 FAT16
/dev/sdd2 65536 2162687 2097152 1G b1 unknown
/dev/sdd3 2162688 4259839 2097152 1G b2 unknown
/dev/sdd4 4259840 15269887 11010048 5.3G 5 Extended
/dev/sdd5 4259872 13168639 8908768 4.3G b4 unknown
/dev/sdd6 13168672 15265791 2097120 1024M b5 unknown
/dev/sdd7 15265824 15269887 4064 2M b6 unknown
I'll throw this disclaimer out there up front that I'm a novice at linux/unix but I know enough (or how to google commands) to be dangerous.
It does use QNX6 as the main filesystem, however, my understanding is that the QNX boot/firmware/IFS partitions can be raw, and are written raw.
I believe 1 is raw despite showing FAT16, 4 is virtual, and 7 no clue. The remaining are QNX6
/dev/sdd1 * 32 65535 65504 32M 6 FAT16
/dev/sdd2 65536 2162687 2097152 1G b1 unknown
/dev/sdd3 2162688 4259839 2097152 1G b2 unknown
/dev/sdd4 4259840 15269887 11010048 5.3G 5 Extended
/dev/sdd5 4259872 13168639 8908768 4.3G b4 unknown
/dev/sdd6 13168672 15265791 2097120 1024M b5 unknown
/dev/sdd7 15265824 15269887 4064 2M b6 unknown
how did you get your system to show all of your available volumes like that? I tried to do that and complains that I did not have a signed application.
11-14-2017, 07:00 PM
#14
Well, I'll be...
Tried to fix the GN issue in v2.2.17011 again and it worked... I think the only difference is I actually used a 32GB microSD card this time instead of the 8GB drives I have laying around.
...so that's fixed. Stlll working on v2.3.
Tried to fix the GN issue in v2.2.17011 again and it worked... I think the only difference is I actually used a 32GB microSD card this time instead of the 8GB drives I have laying around.
...so that's fixed. Stlll working on v2.3.
11-14-2017, 07:02 PM
#15
There is also a case just for trying to install v2.3 over 3.0... it simply throws out a message that says "You already have the latest software" or similar. That's what I redacted from the MY18 section.
11-14-2017, 07:43 PM
#16
11-14-2017, 07:44 PM
#17
yep I discovered that logic a few days ago and had folks downgrade to 2.2 first. This is the first version I’ve seen that contains such version checking logic.
The following users liked this post:
Nchapman (07-15-2020)
11-15-2017, 10:49 AM
#19
LOL!
So after I got GN working on v2.2.17011, I tried to install v2.3 again and now GN has disappeared again.
Checking for updates over WiFi still results in nothing.
I'd like to try to piecemeal v2.3 on there at some point, but with the version checking as it is... I'm not sure it will work after v2.3 is present.
So after I got GN working on v2.2.17011, I tried to install v2.3 again and now GN has disappeared again.
Checking for updates over WiFi still results in nothing.
I'd like to try to piecemeal v2.3 on there at some point, but with the version checking as it is... I'm not sure it will work after v2.3 is present.
11-15-2017, 11:20 AM
#20
LOL!
So after I got GN working on v2.2.17011, I tried to install v2.3 again and now GN has disappeared again.
Checking for updates over WiFi still results in nothing.
I'd like to try to piecemeal v2.3 on there at some point, but with the version checking as it is... I'm not sure it will work after v2.3 is present.
So after I got GN working on v2.2.17011, I tried to install v2.3 again and now GN has disappeared again.
Checking for updates over WiFi still results in nothing.
I'd like to try to piecemeal v2.3 on there at some point, but with the version checking as it is... I'm not sure it will work after v2.3 is present.
Code:
; SYNC3 Consumer Assembly Upgrade - Release 2.3.10 - Only for MY 16 NonNav/NonEU assemblies. ; GN DB installation [SYNCGen3.0_2.3.17109_PRODUCT] ; system prep Item1 = HB5T-14G386-TBB Open1 = SyncMyRide\HB5T-14G386-TBB.tar.gz ; remove Gracenotes DB to make room Item2 = GB5T-14G386-SC Open2 = SyncMyRide\GB5T-14G386-SC.tar.gz Options = AutoInstall ; 2nd half [SYNCGen3.0_ALL] ; gracenotes DB installation Item1 = JL7T-14G423-BA Open1 = SyncMyRide\JL7T-14G423-BA.tar.gz Options = AutoInstall,Delay,Include,Transaction