OEM Power Fold Running Boards installed on a XLT
03-21-2019, 08:22 PM
#121
The FORScan Guy
Hoping Flyforfood, Livnitup or Firerunner can help me I have a Gen 12 2014 FX4 I have the 402A luxury Package with the 8in display with Nav. I purchased a set of OEM power running boards from a 2012 Harley truck with module and lots of the wiring harness. I have cut down the harness and soldered what was needed using the Write up of installation taking power from the sun roof and tying into the MS can wires which I believe are the proper wires they are a twisted pair of violet and a color stripe which I can't recall and a brown with a colored stripe with violets going to violet and I had a grey that went to the brown. What I need help in is Forscan doesn't see the Module so I can't program the IPC. Is there any way to check the module or force Forscan to search more am I using the right MS wires how can I check. Is the a way I can add the line of code. Any help would be thankful as I'am at a standstill here now. Thanks
03-21-2019, 08:26 PM
#122
Thanks for getting back to me. I've tried that a few times hoping it would show Had to take the tune out of truck to also be able to start New profile as it wouldn't recognize with a tune in it.
03-21-2019, 08:29 PM
#123
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
Hoping Flyforfood, Livnitup or Firerunner can help me I have a Gen 12 2014 FX4 I have the 402A luxury Package with the 8in display with Nav. I purchased a set of OEM power running boards from a 2012 Harley truck with module and lots of the wiring harness. I have cut down the harness and soldered what was needed using the Write up of installation taking power from the sun roof and tying into the MS can wires which I believe are the proper wires they are a twisted pair of violet and a color stripe which I can't recall and a brown with a colored stripe with violets going to violet and I had a grey that went to the brown. What I need help in is Forscan doesn't see the Module so I can't program the IPC. Is there any way to check the module or force Forscan to search more am I using the right MS wires how can I check. Is the a way I can add the line of code. Any help would be thankful as I'am at a standstill here now. Thanks
As far as FORScan, @Livnitup will be the best source for info involving that.
03-21-2019, 08:35 PM
#126
The FORScan Guy
If you connect in FORScan and it doesn't see the PRB (Power Running Board) module then I suspect something isn't wired correctly with respect to the MS-CAN wires or it would be found on the network. Let me dig up the wiring diagram and have a look...
03-21-2019, 08:43 PM
#128
Tommy
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,265 Likes
on
2,183 Posts
The following users liked this post:
Damit (03-21-2019)
03-21-2019, 08:46 PM
#129
The FORScan Guy
The following 2 users liked this post by Livnitup:
Damit (03-21-2019),
Firerunner (03-21-2019)
03-21-2019, 09:02 PM
#130
Thanks Livnitup most of those I have and they worked great the only thing I might have wrong is the tie in colors and they are of a heaver gauge wire. Module wires are 22 gauge wires in door sill are 18 maybe 20 and like I said previous one is violet and org I believe the + one is brown and yellow stripe I believe brown for sure is main color
Last edited by Damit; 03-21-2019 at 09:17 PM.