ZeroTX

Actually, I just read the entirety of THIS thread and the only thing mentioned is this: "After pressing lock/unlock on fob, press lock/unlock again and hold button for front windows to go up/down." ... and these instructions do not work. The instructions you listed above are entirely different. HENCE why I asked if someone could explicitly state the steps. Thank you for that ,but no need for the insulting question before it.

Edit: Furthemore, THIS thread https://www.f150forum.com/f118/global-windows-381146/ describes at least 3 other methods for pressing the key fob buttons to make it work.... Either a) some of these are wrong or b) different trucks work differently... either way the SPREADSHEET instructions (the spreadsheet that everyone refers ForScan people to) is WRONG and needs updating.

antho

Insulting question? Come on man! Did the steps work or not? I listed the exact steps that where listed in this thread. I just separated the lock/unlock for the up and down.

ZeroTX

NO,the steps in the thread DO NOT work.

YOU said (correctly) that the steps are "Press unlock twice then hold the unlock
Button to lower.
Press the lock button twice then hold to raise."

The THREAD and the FORSCAN SPREADSHEET say "After pressing lock/unlock on fob, press lock/unlock again and hold button for front windows to go up/down." This DOES NOT work. Please read carefully and you'll see that these do not say the same thing.

-Z

ZeroTX

BTW, THANK YOU for the correct information, it worked right away, while the previously provided instructions didn't.... I just didn't think it was necessary to include a snark along with the helpful information. That's like the time wasters who respond to posts with "search is your friend!" instead of just answering the damn question.

antho

So your not reading the instructions the way they where intended. Instead of writing the up and down procedure separate like i did they lumped them together. There is no lock/unlock button. Its either or. The reason i made a "snark" comment is because folks post questions without reading a thread that has the answer spelled out. That's what it looked like to me but apparently you read the instructions but didn't understand the format they where written. I apologize. Glad you got it worked out and your welcome!

After pressing lock/unlock on fob, press lock/unlock again and hold button for front windows to go up/down.
After pressing lock/unlock on fob, press lock/unlock again and hold button for front windows to goup/down

labmaster02

For the windows up just press and hold the lock once and they go up, otherwise you get the horn honk. Windows down needs the unlock pressed twice and held down on the second press.

Tbsheets

My windows go down fine but not up (by the way after they start going down release and press lock and they stop going all the way down). Press lock, then lock and hold and nothing happens except the horn honks...2018 XL

labmaster02

They should stop going down if the lock button is pressed. You need to recheck the values you inputted.

BCM726-17-01 0101 0101 014A
BCM726-17-02 0101 0101 014B
BCM726-30-01 0101 xxxx xxxx
DDM740-05-01 Dxxx xx
PDM741-05-01 Dxxx xx

Tbsheets

BattleBornSC

I'm new at using Forscan and tried the global windows on my 2016 XLT. After much tinkering around and not getting it to work, I loaded the stock settings and figured I would do more research. After finding this thread, I think it has additional settings that the forscan spreadsheet did not have (I'll double check that after work when I can hook up to the computer).
My question is, how do you access the DDM/PDM build configs? When I connect to the vehicle, I've noticed that I seem to have a much more limited selection of features (If I recall, it's BdyCM, PCM, APIM, and one other). Quite a few of the settings are tweaking modules that I can't seem to access (in this case the DDM/PDM configs).
Do any of you fellas know how to access them?
Also, can you do global windows without having the keyless entry keyfob? I've looked around but can't find a definite answer on that. I have the "standard" keyfob, with lock, unlock, panic, remote start and a key (no push button start).