FORScan - software to enable/disable features in your truck
#7841
The Source
Here you go boys... let me know. This one was fun to figure out. I was previously restricted to low beams only and any other change would give an invalid configuration error in FORScan. Well this changes that...
Thread for all DRL discussion (to not clutter up this one): https://www.f150forum.com/f118/setti...t-find-380225/
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = Disabled / Parking Lights Only (See change below)
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
Optional: Enable DRL Parking Lights:
Can be combined with other DRL options above
726-26-02: x1xx xxxx xxxx
Optional: Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Note: To test... DRLs are only active when vehicle is on, headlight switch is in automatic headlights position, and transmission is in Drive. Engine does not have to be running and E-Brake can be engaged.
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
Thread for all DRL discussion (to not clutter up this one): https://www.f150forum.com/f118/setti...t-find-380225/
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = Disabled / Parking Lights Only (See change below)
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
Optional: Enable DRL Parking Lights:
Can be combined with other DRL options above
726-26-02: x1xx xxxx xxxx
Optional: Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Note: To test... DRLs are only active when vehicle is on, headlight switch is in automatic headlights position, and transmission is in Drive. Engine does not have to be running and E-Brake can be engaged.
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
Last edited by DanMc85; 04-23-2017 at 03:22 PM.
The following 26 users liked this post by DanMc85:
'MURICA (09-23-2017),
1911Bandit (04-24-2017),
1st-F-150 (04-22-2017),
2016 FX4x4 (04-28-2017),
Airborne_Ape (04-23-2017),
and 21 others liked this post.
#7842
Here you go boys... let me know. This one was fun to figure out. I was previously restricted to low beams only and any other change would give an invalid configuration error in FORScan. Well this changes that...
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
-
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
-
I tried to do the fog light DRL yesterday with the spreadsheet values and it did not work (wouldn't write), tried dan's values in this post and fog's work as DRL's now. I only tried the low beams and fog's separately, but the new values work on my truck.
Thanks to everyone who's contributed in this thread so far, it's all a amazing stuff. Big thanks to livin for his guide and dan for helping out us F-150 guys when he doesn't have one himself lol.
#7843
Senior Member
iTrader: (1)
Here you go boys... let me know. This one was fun to figure out. I was previously restricted to low beams only and any other change would give an invalid configuration error in FORScan. Well this changes that...
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
The following 3 users liked this post by i8iridium:
#7844
the TPMS will also reset while parked. Left the truck over night, started it today and all the pressures were displayed
#7845
Senior Member
I can confirm also that this works. Great work Dan! I set it to the turns and it works just as expected. I'm finally able to remove the relay and other hardwiring I had to do this! Only thing is I have switchback bulbs which are white for park/running lights and flash amber for turns. So my DRL is amber instead of white.
I wonder if there is a setting to use the park/running lights as DRL so it will light up in white, and not in amber as it is doing now with the turns (option 8). I have other Morimoto switchback halos on my fogs which are tied into the same circuit. They are yellow as well instead of white with this change. I'll have to experiment a little I guess.
I wonder if there is a setting to use the park/running lights as DRL so it will light up in white, and not in amber as it is doing now with the turns (option 8). I have other Morimoto switchback halos on my fogs which are tied into the same circuit. They are yellow as well instead of white with this change. I'll have to experiment a little I guess.
#7846
The Source
I can confirm also that this works. Great work Dan! I set it to the turns and it works just as expected. I'm finally able to remove the relay and other hardwiring I had to do this! Only thing is I have switchback bulbs which are white for park/running lights and flash amber for turns. So my DRL is amber instead of white.
I wonder if there is a setting to use the park/running lights as DRL so it will light up in white, and not in amber as it is doing now with the turns (option 8). I have other Morimoto switchback halos on my fogs which are tied into the same circuit. They are yellow as well instead of white with this change. I'll have to experiment a little I guess.
I wonder if there is a setting to use the park/running lights as DRL so it will light up in white, and not in amber as it is doing now with the turns (option 8). I have other Morimoto switchback halos on my fogs which are tied into the same circuit. They are yellow as well instead of white with this change. I'll have to experiment a little I guess.
Enable Parking Lights w/DRL Enabled:
726-26-02: x1xx xxxx xxxx
Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
and use one of the other DRL settings like Dedicated or something else. (Dedicated will give you two DTCs with nothing connected to the outputs, FYI).
- Dan
Last edited by DanMc85; 04-21-2017 at 01:27 PM.
#7847
Senior Member
Try this with your aftermarket lights:
Enable Parking Lights w/DRL Enabled:
726-26-02: x1xx xxxx xxxx
Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
and use one of the other DRL settings like Dedicated or something else. (Dedicated will give you two DTCs with nothing connected to the outputs, FYI).
- Dan
Enable Parking Lights w/DRL Enabled:
726-26-02: x1xx xxxx xxxx
Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
and use one of the other DRL settings like Dedicated or something else. (Dedicated will give you two DTCs with nothing connected to the outputs, FYI).
- Dan
My 726-26-02 is 0100 xxxx xxxx
I tried the "08" option at 726-50-01, still lights amber for DRL
I tried the "10" option at 726-50-01, and nothing lights up.
I tried other combinations and got incompatible configuration.
#7848
Tried the Fogs for DRL. Didn't work for me. Should I see other options in IPC lighting other then daytime lights? I have it checked off but after the change I get no daytimes at all. I had the CDN DRL disable activated on my truck prior.
Here you go boys... let me know. This one was fun to figure out. I was previously restricted to low beams only and any other change would give an invalid configuration error in FORScan. Well this changes that...
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
Optional: Enable Parking Lights w/DRL Enabled:
726-26-02: x1xx xxxx xxxx
Optional: Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
Allow All Alternate DRL Options (Restrictions Removed - No Invalid Configuration Errors):
BdyCM (As-Built Modifications)
Allow All DRL Choices:
726-45-01: xxxx 7Fxx xxxx
Enabled DRL Selection:
726-50-01: XXxx
XX:
01 = DRL Master Disable
02 = Low Beams
04 = Front Fog Lamps
08 = Front Turn Lamps
10 = Dedicated DRL Lights (LED Light Bars/Strips) - Enables BCM DRL Outputs - C2280F (F-150) Pins 36 (Right) and 40 (Left)
20 = High Beams
40 = Low Beams and Dedicated DRL Lights
Optional: Enable Parking Lights w/DRL Enabled:
726-26-02: x1xx xxxx xxxx
Optional: Disable DRL Switchback w/Turn Signal:
726-26-02: xxx0 xxxx xxxx
On/Off for these is controlled from the Instrument Cluster DRL Control.
I know many of you change wiring and such to accomplish some of these which can be now changed in seconds... so enjoy!
If you feel like buying me a round: PayPal Donation
- DanMc85
Enable IPC DRL Control (If Missing): http://www.2gfusions.net/showthread....85446#pid85446
-
#7849
Does anyone know if the automatic engine start/stop feature can be disabled? It's on automatically upon startup and can be turned off with the button by the radio, but I'm wondering if it can permanently be disabled through FORScan.
#7850
Awesome work!!