FORScan - software to enable/disable features in your truck
#7461
2015 F150 Guy
How cool would it be if Sync would cycle thru all the stored wallpapers automatically, say every hour ?
DayDreamin,
TomJV
DayDreamin,
TomJV
#7462
Texas A&M Aggie
I tried to help program a 2017 XLT the other day and no matter which IPC module I clicked on it wouldn't pull up any values. Was I doing something incorrect or are the '17's different with their programming? I've got the OBD MX Bluetooth tool, have no issues getting into everything on my '16 Lariat, or UNBROKEN's '16 Platinum.
#7463
The FORScan Guy
Thread Starter
I tried to help program a 2017 XLT the other day and no matter which IPC module I clicked on it wouldn't pull up any values. Was I doing something incorrect or are the '17's different with their programming? I've got the OBD MX Bluetooth tool, have no issues getting into everything on my '16 Lariat, or UNBROKEN's '16 Platinum.
#7465
Originally Posted by DanMc85
Mileage is stored in the IPC only and is then populated into about 3 other modules (can see via FORScan) however, it is not actually saved there. If you swap clusters the mileage in the other modules will change accordingly as well. However, the other modules use a slightly different algorithm and appear to be off by a few miles or FORScan has the KM to MI conversion formula slightly wrong, one of the two.
Mileage is stored in the IPC EEPROM and the IPC Firmware ship SPC****. EEPROM usually populates the SPC chip when changed.
Mileage is stored in the IPC EEPROM and the IPC Firmware ship SPC****. EEPROM usually populates the SPC chip when changed.
I am planning on sending it to anthony soon but till then.....
#7466
Forscan mod for remote tailgate release?
Now that I installed the damper, any way to use a 500a base Lariat remote to open the tailgate? I know the truck can do it with another remote type. I can also open it remotely with the keypad by pressing 5-6 immediately after unlocking the truck with the keypad.
#7467
Purchased an ACM out of an 2015 expedition to enable the HD Radio in my 2015 501 SCREW. I found the 1 or 2 lines in the APIM to modify and got those modified, but some of the values in the spreadsheet didnt match up to values that I had. I made the changes that I knew needed to be made and moved on to program the ACM. I loaded my AS built values into the ACM and then edited the values to enable HD-Radio. Everything works ok, but the seatbelt/warning chimes and object detection beeps no longer are played through the audio system. They are only played through the small speaker somewhere in the dash. Anybody know how to address this? I have searched regarding HD Radio enablement and havent found what I need
SYNC 2 MFT 8" screen
Here are the APIM values that i changed:
7D0-01-01 xxxx xxx2 xxxx to xxxx xxx3 xxxx
ACM Values that I changed:
727-01-01 AsBuillt - 1801 1A08 006B
727-01-01 HD Radio - 1001 1A08 006B
727-01-02 AsBuilt - 0645-7C - Not Altered
727-04-01 AsBuilt - 0001 0255 53DE
727-04-01 HD Radio - 0001 0155 53DE
Anybody have any ideas what I need to change to get the chimes/warnings back?
SYNC 2 MFT 8" screen
Here are the APIM values that i changed:
7D0-01-01 xxxx xxx2 xxxx to xxxx xxx3 xxxx
ACM Values that I changed:
727-01-01 AsBuillt - 1801 1A08 006B
727-01-01 HD Radio - 1001 1A08 006B
727-01-02 AsBuilt - 0645-7C - Not Altered
727-04-01 AsBuilt - 0001 0255 53DE
727-04-01 HD Radio - 0001 0155 53DE
Anybody have any ideas what I need to change to get the chimes/warnings back?
#7468
The Source
Correct, however if you have been to the dealership since you were at 10500 or if your truck has synced the mileage through sync (check syncmyride.com) over wifi or cellular then they will know it was changed.
#7469
The Source
Purchased an ACM out of an 2015 expedition to enable the HD Radio in my 2015 501 SCREW. I found the 1 or 2 lines in the APIM to modify and got those modified, but some of the values in the spreadsheet didnt match up to values that I had. I made the changes that I knew needed to be made and moved on to program the ACM. I loaded my AS built values into the ACM and then edited the values to enable HD-Radio. Everything works ok, but the seatbelt/warning chimes and object detection beeps no longer are played through the audio system. They are only played through the small speaker somewhere in the dash. Anybody know how to address this? I have searched regarding HD Radio enablement and havent found what I need
SYNC 2 MFT 8" screen
Here are the APIM values that i changed:
7D0-01-01 xxxx xxx2 xxxx to xxxx xxx3 xxxx
ACM Values that I changed:
727-01-01 AsBuillt - 1801 1A08 006B
727-01-01 HD Radio - 1001 1A08 006B
727-01-02 AsBuilt - 0645-7C - Not Altered
727-04-01 AsBuilt - 0001 0255 53DE
727-04-01 HD Radio - 0001 0155 53DE
Anybody have any ideas what I need to change to get the chimes/warnings back?
SYNC 2 MFT 8" screen
Here are the APIM values that i changed:
7D0-01-01 xxxx xxx2 xxxx to xxxx xxx3 xxxx
ACM Values that I changed:
727-01-01 AsBuillt - 1801 1A08 006B
727-01-01 HD Radio - 1001 1A08 006B
727-01-02 AsBuilt - 0645-7C - Not Altered
727-04-01 AsBuilt - 0001 0255 53DE
727-04-01 HD Radio - 0001 0155 53DE
Anybody have any ideas what I need to change to get the chimes/warnings back?
Just unplug the battery for 30 minutes and they should sync back up.
It isn't anything wrong with your asbuilt.
The following users liked this post:
rossg (03-29-2017)