FORScan - software to enable/disable features in your truck
#3911
Hey, folks.
I've been interested in adding the factory 110v inverter. I have the fuses in place and, if it's like the subwoofer, the wiring harness is to be found somewhere.
Anyway, assuming that I'm correct, do I need to activate anything in the BCM or other modules? I scanned the testing spreadsheet but didn't see anything but timeout settings.
Thanks.
I've been interested in adding the factory 110v inverter. I have the fuses in place and, if it's like the subwoofer, the wiring harness is to be found somewhere.
Anyway, assuming that I'm correct, do I need to activate anything in the BCM or other modules? I scanned the testing spreadsheet but didn't see anything but timeout settings.
Thanks.
#3912
Flaccid Member
#3914
Beer Gut Extraordinaire
Well, I might be the only member in Canada with functioning auto fold tow mirrors!!
The pin reversal went easy, I picked up a Stanley precision screwdriver kit from Walmart and made short work of it, got both sides done in about 45 minutes with a beer and smoke break in between.
I didn't do the programming myself, a local member did it as I don't have the equipment yet, but I am very happy with the way this function operates. Because if you use the switch inside, it inhibits the auto-fold from working until you use the switch inside again, which is beneficial for backing in and out of my garage.
I also have the global window function now too which is very helpful!
The pin reversal went easy, I picked up a Stanley precision screwdriver kit from Walmart and made short work of it, got both sides done in about 45 minutes with a beer and smoke break in between.
I didn't do the programming myself, a local member did it as I don't have the equipment yet, but I am very happy with the way this function operates. Because if you use the switch inside, it inhibits the auto-fold from working until you use the switch inside again, which is beneficial for backing in and out of my garage.
I also have the global window function now too which is very helpful!
#3915
Senior Member
Are the guys tilting the mirrors past the point of where you can see directly behind your truck to where you are just looking at the ground on either side of your vehicle? Or are you splitting the difference? I am curious because I don't really see the point of doing it at all. Educate me please.
#3916
Sorry to bring an older post up but was wondering if anyone now has any thoughts on this? It would be nice to be able to set the buttons to your liking. I wish the Reverse and Forward buttons on the right side of the wheel would go up and down one channel at a time instead of just through the presets.
#3917
Setting it was tricky and took a couple attempts, I also had to recall the memory setting when I was done.
Try this:
Reverse Tilt Mirror Calibration:
1) Switch the ignition on
2) Press the memory button
3) Select the mirror you want to adjust
4) Put your vehicle into reverse (R) and let the mirror automatically tilt until it stops
5) When the mirror is in its tilted position and is no longer moving, adjust it with the controls
6) Hold the memory button for 5 seconds to save the setting
7) Press the mirror button and return to park (P)
8) Hold memory button again
Here is my spreadsheet of settings I have confirmed on my 2016 Explorer Platinum
https://www.icloud.com/numbers/0AtiY..._2016_Explorer
Thank you to DanMc85 and Livnitup! I now have remote global windows open/close, reverse tilt mirrors, and no double honk on my Explorer!
Last edited by PlatinumOwner; 12-06-2016 at 12:04 PM.
The following 6 users liked this post by PlatinumOwner:
Airborne_Ape (12-31-2016),
D.WRECK (09-24-2019),
jdroller (12-31-2016),
lambinator (01-07-2017),
Rob O (01-26-2017),
and 1 others liked this post.
#3918
Senior Member
So I've got something funny going on. I have aftermarket LEDs in my front turn signals and rear brake/turns. I have resistors on the front but not the rear. The lights all flash properly but I get hyperflash on my IPC. I have enabled the bambi mod with LED turns but still get hyperflash (bambi mod works). Any ideas?
I have also (I believe) disabled light outage detection.
I have also (I believe) disabled light outage detection.
#3919
What values do you have in 726-27-01 ?
#3920
Senior Member