FORScan - software to enable/disable features in your truck
10-23-2017, 07:26 PM
It's my first day
Originally Posted by longbedbob
have some static that I'm trying to eliminate.
Is it possible that my noise is due to the changes I made previously?
Is it possible that my noise is due to the changes I made previously?
Whether or not thats even your issue is debatable.
There are also line level output adjustments in the ACM and EQ settings you can have a peek at.
Radio adjustment isnt my thing. My short answer is yes but I would have to think it could be anything from a bad wire shield / ground or any one of your custom modified parts.
Your best insight into this might come if you PM TexasFording, JM061 or DanMc85.
Last edited by Airborne_Ape; 10-23-2017 at 07:47 PM.
10-23-2017, 07:33 PM
It's my first day
Originally Posted by tgoin
folks may have missed my question about the tutorial.
Is there an alternate source that DOES have audio?
Is there an alternate source that DOES have audio?
I cant upload any imovie creations until the weekend though.
The following users liked this post:
GTA150 (10-24-2017)
10-23-2017, 07:42 PM
It's my first day
Originally Posted by 4RDtough
Can Forscan code the vehicle to remove the memory seat recall restriction? Normally, vehicle must be in park or neutral to be recalled.
- Second I doubt you can use ForScan to bypass the vss in the seat module considering we can’t bypass it anywhere else.
- Third. I would suggest grabbing the wiring diagram for your memory module to see if the module has a switched 12V enable lead going to it from the BCM. you might be able to hardwire bypass just like we can for the spotlight module on 13 gens. if you need someone to decipher a wiring diagram go ahead and post it online but that brings me to my first point...
wrong thread. There is a dedicated 12 gen F150 section on this website.
Last edited by Airborne_Ape; 10-23-2017 at 07:51 PM.
10-23-2017, 07:46 PM
There is a radio hissing noise that can be corrected or so I think with a firmware update to the APIM. I was reading about it on an EU focus thread and I think JM061 had it sorted out.
Whether or not thats even your issue is debatable.
There are also line level output adjustments in the ACM and EQ settings you can have a peek at.
Radio adjustment isnt my thing. My short answer is yes but I would have to think it could be anything from a bad wire shield / ground or any one of your custom modified parts.
Whether or not thats even your issue is debatable.
There are also line level output adjustments in the ACM and EQ settings you can have a peek at.
Radio adjustment isnt my thing. My short answer is yes but I would have to think it could be anything from a bad wire shield / ground or any one of your custom modified parts.
Those modules won't even load. Basically it's the BCM and a few others, but nothing concerning audio.
10-23-2017, 07:49 PM
It's my first day
Originally Posted by longbedbob
Thanks.
Those modules won't even load. Basically it's the BCM and a few others, but nothing concerning audio.
Those modules won't even load. Basically it's the BCM and a few others, but nothing concerning audio.
10-23-2017, 08:03 PM
10-23-2017, 08:14 PM
Senior Member
Just out of curiosity, where is the fake engine noise generated? APIM, radio/module...!???
10-23-2017, 08:20 PM
The FORScan Guy
Thread Starter
back to business here guys. In all that FUN ... folks may have missed my question about the tutorial on backing up modules - and the fact that the youtube version has no audio.
Is there an alternate source that DOES have audio? To me, it's critical to make a good backup before starting.
Is there an alternate source that DOES have audio? To me, it's critical to make a good backup before starting.
10-23-2017, 08:26 PM
It's my first day
Originally Posted by OrionPax
Just out of curiosity, where is the fake engine noise generated? APIM, radio/module...!???
JM061 is the expert on that. As for 2018s I havent a clue but I assume its the same.
10-23-2017, 09:43 PM
Senior Member
I have enabled the Lincoln theme and I really like the colors considering my truck is black/caribou. I am not really a fan of having the Lincoln splash screen and wanted to either change it to the Raptor (I can dream) or back to the Ford. Has anyone tried this? If so can you share the settings that you used? If not I will play with it and post my findings. Thanks!
APIM 7D0-02-01 xxxx-05xx-xxxx
(Note: the original response to this by @texasford indicated it was not possible. I enabled the Lincoln theme on mine tonight and found that response to be incorrect so I thought it worth providing an update, as it appears you can in fact enable whichever of listed splash screens you want but the shutdown screen will remain the Lincoln one)
Last edited by GreenScrew; 10-23-2017 at 11:22 PM.