Backup Camera Install
#61
Thanks for the reply Gordy. What would be the correct way to clear the error inside forscan to see if it comes back. All lights are working properly. What would I need to do to get the backup lines then?
Appreciate the support and Merry Christmas folks.
Appreciate the support and Merry Christmas folks.
#64
Senior Member
Thread Starter
#65
#66
Senior Member
Thread Starter
Originally I installed the RCA cable as pictured but I didn't keep it very long. Decided I would remove it and just run the cable uninterrupted all the way to the back.
Edit to answer your second question: yes, after a quick Forscan mod to "tell" your system that there is a camera installed you should be good to go. (Except for a power source to the camera of course.)
Edit to answer your second question: yes, after a quick Forscan mod to "tell" your system that there is a camera installed you should be good to go. (Except for a power source to the camera of course.)
Last edited by D2Abbott; 12-12-2019 at 10:46 PM.
The following users liked this post:
D2Abbott (12-12-2019)
#68
@D2Abbott I just completed the original directions to a tee and it worked awesome. Thank you so much! I used:
Reverse Backup Camera,RAAYOO L002 170 Degree Wide View Angle 2-in-1 Universal Car Front/Side/Rear View Camera,2 Installation Options,Removable Guildlines,mirror non-mirror image,12V only
Drilled the camera into the factory tailgate handle and then tapped into the appropriate wires at the fender connector with:
GaoZo Speaker Wire To RCA Female Adapter For High-Level Signal Connection To Amp (Black/Red)
Then dialed up the two changes in the forscan spreadsheet. Like butter!
For those of you that are hesitant to try it, it’s about as easy as it gets. I say go for it!
Reverse Backup Camera,RAAYOO L002 170 Degree Wide View Angle 2-in-1 Universal Car Front/Side/Rear View Camera,2 Installation Options,Removable Guildlines,mirror non-mirror image,12V only
Drilled the camera into the factory tailgate handle and then tapped into the appropriate wires at the fender connector with:
GaoZo Speaker Wire To RCA Female Adapter For High-Level Signal Connection To Amp (Black/Red)
Then dialed up the two changes in the forscan spreadsheet. Like butter!
For those of you that are hesitant to try it, it’s about as easy as it gets. I say go for it!
Last edited by drburn1718; 12-17-2019 at 10:17 PM.
The following users liked this post:
D2Abbott (12-17-2019)
#69
Junior Member
Rear Wires
So after some more investigation I found that the bundle of wires from the C316 under hood harness splits off to several smaller harnesses at the back. The two white/green and brown/violet wires are found in a separate connector (shown in blue below) that has a protective cap on it (the same one found in your glove box for protecting the camera harness during tailgate removal). The two wires for the power tailgate lock splits off into another harness (shown in pink) that goes to the gate.
So I am not sure if I am pre-wired or not but it seems I could just tap into the blue harness for the camera connection assuming that I am tracing the right wires in the first place! This is a '15 XL with 4.2" non nav display FWIW.
So I am not sure if I am pre-wired or not but it seems I could just tap into the blue harness for the camera connection assuming that I am tracing the right wires in the first place! This is a '15 XL with 4.2" non nav display FWIW.
#70
Junior Member
Same plug
have the same setup on my XL. Does anyone know what the gray plug is for or what number it is? I don't want to run the wires from the front if I don't have to. I am trying to verify if it has the right wires running to it.
So after some more investigation I found that the bundle of wires from the C316 under hood harness splits off to several smaller harnesses at the back. The two white/green and brown/violet wires are found in a separate connector (shown in blue below) that has a protective cap on it (the same one found in your glove box for protecting the camera harness during tailgate removal). The two wires for the power tailgate lock splits off into another harness (shown in pink) that goes to the gate.
So I am not sure if I am pre-wired or not but it seems I could just tap into the blue harness for the camera connection assuming that I am tracing the right wires in the first place! This is a '15 XL with 4.2" non nav display FWIW.
I
So I am not sure if I am pre-wired or not but it seems I could just tap into the blue harness for the camera connection assuming that I am tracing the right wires in the first place! This is a '15 XL with 4.2" non nav display FWIW.
I