2015+ Overhead Console Intrusion Sensor Retrofit
#11
Tommy
Thread Starter
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,264 Likes
on
2,183 Posts
@FMFDoc, The part for 15 - 17 is FL3Z-18519A70-xxx The "xxx" is what differenciates the different color/trim/options
A good place to look is of course eBay, being that you can see a picture of the actual product and possibly get the full part # from the description. Another good source of used parts is Car-Part.com,
Again, this is a good choice because you can see the actual product most times.
Quick Tip:
The consoles are modular, If you find one for a good price that is the correct color but has an option yours may or may not have (such as sunroof switch) You can remove the panels with the sensor holes and transfer them to your console
A good place to look is of course eBay, being that you can see a picture of the actual product and possibly get the full part # from the description. Another good source of used parts is Car-Part.com,
Again, this is a good choice because you can see the actual product most times.
Quick Tip:
The consoles are modular, If you find one for a good price that is the correct color but has an option yours may or may not have (such as sunroof switch) You can remove the panels with the sensor holes and transfer them to your console
The following users liked this post:
FMFDoc (05-21-2018)
#12
Senior Member
iTrader: (1)
When I get off work this afternoon I'll get you a starting point to use for searching.
You can replace the roof harness, but you will still need to run the wires from the BCM down the passenger side wiring channel to where your roof harness connects to the rest of the trucks harness.
You can replace the roof harness, but you will still need to run the wires from the BCM down the passenger side wiring channel to where your roof harness connects to the rest of the trucks harness.
#14
Senior Member
Firerunner, this is a great write-up. I've been waiting on this since Boosted showed it was possible. Do you have the part number for the female terminals for the 1241634-1 connector? Does the part number for the console come with the sensors? Sometimes it hard to tell with the diagrams.
Thanks
Thanks
The following 2 users liked this post by labmaster02:
2016BoostedGreyGoose (05-22-2018),
Firerunner (05-22-2018)
The following users liked this post:
Firerunner (05-22-2018)
The following 2 users liked this post by Ryan B:
Firerunner (05-22-2018),
labmaster02 (05-22-2018)
#17
Tommy
Thread Starter
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,264 Likes
on
2,183 Posts
#18
Tommy
Thread Starter
iTrader: (3)
Join Date: Nov 2012
Location: Greenville, North Carolina
Posts: 6,022
Received 4,264 Likes
on
2,183 Posts
Firerunner, this is a great write-up. I've been waiting on this since Boosted showed it was possible. Do you have the part number for the female terminals for the 1241634-1 connector? Does the part number for the console come with the sensors? Sometimes it hard to tell with the diagrams.
Thanks
Thanks
I know when several of us bought Lariat dashes they did come with the two pads, which are listed with separate part #'s in the diagram.
#20
Working on this mod and seem to have run into problems. Got the needed parts from a donor Lariat's overhead console and the harness from 2016BoostedGreyGoose.Install went fine, forscan changes made and then the problems began.
I cant seem to compete the BdyCM calibration. When running the BdyCM Local Interconnect Network New Module Calibration I get the following message:
"Test Aborted. Perform a self test to identify diagnostic trouble codes." This happens at the 8% mark of the test.
Went over to vehicle tests tab and ran the DTC on demand test and the only Code I get is B109F-Intrusion Sensor Module (Not configured)
Also, when I check the DTC codes the only one that comes up is the same one during the self test: B109F-Intrusion Sensor Module (Not configured)
I assume that the DTC code is expected as the module calibration never completed.
I confirmed and reconfirmed the Forscan settings and the electrical connections are in the correct modules and locations. (Confirmed three times).
Any suggestions on why the module calibration is aborting? Forgot to add: 2018 F150 XLT w/ perimeter alarm from factory..
Thanks in advance..
I cant seem to compete the BdyCM calibration. When running the BdyCM Local Interconnect Network New Module Calibration I get the following message:
"Test Aborted. Perform a self test to identify diagnostic trouble codes." This happens at the 8% mark of the test.
Went over to vehicle tests tab and ran the DTC on demand test and the only Code I get is B109F-Intrusion Sensor Module (Not configured)
Also, when I check the DTC codes the only one that comes up is the same one during the self test: B109F-Intrusion Sensor Module (Not configured)
I assume that the DTC code is expected as the module calibration never completed.
I confirmed and reconfirmed the Forscan settings and the electrical connections are in the correct modules and locations. (Confirmed three times).
Any suggestions on why the module calibration is aborting? Forgot to add: 2018 F150 XLT w/ perimeter alarm from factory..
Thanks in advance..
Last edited by FMFDoc; 06-01-2018 at 11:06 PM.