Is a 95 5.0L TPS the adjustable type?
#1
Senior Member
Thread Starter
Is a 95 5.0L TPS the adjustable type?
Gonna replace this, ordered a Motorcraft from RockAuto from advice here. I've watched a bunch of videos and similar years, the videos just drop it in the original spot. But I've seen one where it was important to get it in same position as before as it was adjustable.
I know what you are saying...is it broken? I've changed IAC, cleaned throttle body (as best as I could, didn't remove), cleaned MAF, new vacuums and all seems to make the truck better. But just once a while, I'm still getting a weird hesitation at around 20 and 45mph (stutter, hesitation, etc).
So watching a lot of diagnosis videos, I just realized all of these are kinda intertwined and work together. So I think this is the last piece of the puzzle to clean out or change with a better one (it's over 225K miles so time to replace stuff).
I know what you are saying...is it broken? I've changed IAC, cleaned throttle body (as best as I could, didn't remove), cleaned MAF, new vacuums and all seems to make the truck better. But just once a while, I'm still getting a weird hesitation at around 20 and 45mph (stutter, hesitation, etc).
So watching a lot of diagnosis videos, I just realized all of these are kinda intertwined and work together. So I think this is the last piece of the puzzle to clean out or change with a better one (it's over 225K miles so time to replace stuff).
#2
Senior Member
iTrader: (1)
You can test it with a voltmeter to see if there's actually a problem with it before you change it. Testing the old one even if you change it will tell you if that's actually the problem and it will also give you a little practice so you can make sure the new one is "dialed in" just right.
Look on page 2 or 3 for "testing the TPS". You'll want to do the signal wire test. And maybe bump it up for other people to find.
Look on page 2 or 3 for "testing the TPS". You'll want to do the signal wire test. And maybe bump it up for other people to find.
The following users liked this post:
ericantonio (09-24-2015)
#3
Senior Member
Thread Starter
That's a good idea. I was just gonna remove and replace but yeah, I might as well take longer and actually learn how to test it even though I'm gonna replace it. I saw a really good video of one. Let me keep looking in the How-to section.
The following users liked this post:
ericantonio (09-24-2015)
#5
Senior Member
Thread Starter
His write up is here:
https://www.f150forum.com/f10/testin...ht=testing+tps
https://www.f150forum.com/f10/testin...ht=testing+tps
So in the video above, the throttle is off the engine. And I'm assuming the TPS is still plugged in for the testing. But how do you test it with moving the throttle?
I watched this guy last night, tps testing
http://tinyurl.com/pucncnc
And a couple of other ones. For an inexperienced newbie like me, it's a little daunting cause a couple of videos warn that if I do this wrong, I'll toast something and I'll be SOL!
Last edited by ericantonio; 09-24-2015 at 05:43 PM. Reason: more
#6
1994 F150 XLT 5.8L 2wd
It helps to have a second set of hands, just use the two probes to push into the wires of the ground and the signal, hold them there while someone turns the throttle control. You would be hard pressed to fry something so don't overthink the process, just make sure you properly identify the wires first. Key must be on, engine off.
#7
Senior Member
Thread Starter
I tried testing it and I thought there was a problem with the way I was doing it. I was doing the "safety pin" method of sticking it in the wire. It read .2. Hmmm, so I decided to just remove the throttle completely and replace it.
What a MESS!!! Broke some of the old brittle hoses and coolant leaked. Better now that it breaking while driving.
Inside the throttle, behind the round piece that opens and closes, was DIRTY!!!! I will need to get some of those stiff round wire brushes for my drill and clean the entire throttle body. Inside the intake manifold (didn't put a flashlight through it but I will tomorrow) was dirty!!! Caked in there with carbon. And there is a hole between the top and bottom air intake that was completely clogged. So I'll be spending a lot of time cleaning this out tomorrow. Worth the effort I think.
When putting in the new one, I'll try sticking a pin in the wire before I install the throttle. Oh and yeah, I broke the ceramic or plastic piece of the accelarator cable. Its the 2" section just before the end that attaches to the throttle. I'll start another thread with that.
What a MESS!!! Broke some of the old brittle hoses and coolant leaked. Better now that it breaking while driving.
Inside the throttle, behind the round piece that opens and closes, was DIRTY!!!! I will need to get some of those stiff round wire brushes for my drill and clean the entire throttle body. Inside the intake manifold (didn't put a flashlight through it but I will tomorrow) was dirty!!! Caked in there with carbon. And there is a hole between the top and bottom air intake that was completely clogged. So I'll be spending a lot of time cleaning this out tomorrow. Worth the effort I think.
When putting in the new one, I'll try sticking a pin in the wire before I install the throttle. Oh and yeah, I broke the ceramic or plastic piece of the accelarator cable. Its the 2" section just before the end that attaches to the throttle. I'll start another thread with that.
Trending Topics
#8
Senior Member
Thread Starter
TPS is in. Throttle and intake manifold is super clean. I still couldn't get a good reading on that black wire! Maybe I need a real piercing probe. I'll try again when it cools off a little later today
Right now, it's running a bit high on idle. But it sure does take off from stop and no hesitation whatsoever in between shifting gears!
Right now, it's running a bit high on idle. But it sure does take off from stop and no hesitation whatsoever in between shifting gears!
#9
Senior Member
iTrader: (1)
I just use the point of the m/m probe and stick it right through the insulation on the wire. Some may disagree with doing that but I haven't had any issues. You can use some liquid silicone to seal it after if you want to be fussy.
Anyway, doing it that way, I get a good reading.
Anyway, doing it that way, I get a good reading.
The following users liked this post:
ericantonio (09-28-2015)
#10
Senior Member
Thread Starter
I found this post:
http://tinyurl.com/o49gw7d
Looks like Motorola TPS uses the GREEN wire as the TP signal wire.
I'll try it again tomorrow. Maybe I can find a piercing probe somewhere. But I'll try the safety pin method and I have some hobby paint I can paint it over.
http://tinyurl.com/o49gw7d
Looks like Motorola TPS uses the GREEN wire as the TP signal wire.
I'll try it again tomorrow. Maybe I can find a piercing probe somewhere. But I'll try the safety pin method and I have some hobby paint I can paint it over.