Topic Sponsor
Tires, Wheels and Suspension "How-To" articles pertaining to the Tires, Wheels and Suspension of an F150.

The Definitive Bilstein 5100 DIY Install Thread

Thread Tools
 
Search this Thread
 
Old 04-01-2013, 01:09 PM
  #1  
Junior Member
Thread Starter
 
Action Jack's Avatar
 
Join Date: Feb 2013
Posts: 23
Received 34 Likes on 6 Posts
Post The Definitive Bilstein 5100 DIY Install Thread

Wanted to start this thread for two reasons:

1. Share all of the knowledge I compiled while researching how to do a driveway install of front Bilstein 5100 shocks

2. Have everyone share pictures of their trucks with Bilsteins installed to make it easier to choose which level of ride height adjustment you want to go with.

I’ve done quite a bit of research here on the forums determining whether or not to attempt swapping my stock front shocks for the Bilstein 5100s. After I took into account that I could get the shocks much cheaper on Amazon ($97/each), alignment is much cheaper if you shop around and I could skip on labor charges, I did the math and found I would save about $350 by doing the install myself. Not to mention, it is exceptionally satisfying to complete a job like this yourself. I found a number of hints and tips online and in the forums, but no definitive instructions on how to do the install. So here it is…

Preliminary notes: This job should take about 3 hours. It really helps to have a buddy helping, two is even better, a cooler full of beer doesn’t hurt either. If you’re missing any of the necessary tools especially a lift, jack stands, spring compressors, remember that any auto parts store is happy to rent them to you for absolutely free. The instructions below don’t include an impact wrench, if you have one it would be exceptionally helpful, but not necessary.

**Sorry the pictures are after the fact, my camera ran out of juice just as we started the job.

- Disconnect Negative Battery Terminal
Tools Needed: Ratchet with 8mm socket
Instruction: On newer trucks it is recommend that you detach the negative
battery terminal to save your EPAS (Electronic Power Assist
Steering)

- Get the truck on lifts
Tools Needed: Floor jack, jack stands
Instruction: Lift the truck up off the wheels and place jack stands as wide
apart as possible on the center frame area

- Remove wheel
Tools Needed :21mm lug wrench (for stock lugs)
Instructions: Pretty straight forward, removed the lugs, remove the wheel
and set aside. This is a good opportunity to clean the inside
of your wheels a well.

- Remove 3 nuts off top of shock mount
Tools Needed: Ratchet with 15mm deep socket, or ratcheting box wrench
Instructions: There are a few wires in the way, but they’re easy to work
around the and nuts should come off easily



- Remove large bolt from lower shock mount
Tools Needed: Ratchet with 27mm socket, 24”+ cheater bar and 30mm box
wrench
Instructions: Although this step seems a bit daunting it really isn’t all too
bad. You can break the bolt free without holding the nut,
but you will need the box wrench after the first few turns.



- Disconnect sway bar
Tools Needed: 18mm box wrench, Ratchet with 8mm standard socket
Instructions: The sway bar can be disconnected from either the top or
bottom. The top was easily accessible so I went that route.
You will have to hold the 18mm nut and ratchet the center
post at the same time to remove.



- Remove brake line bracket
Tools Needed: Ratchet with 10mm standard socket
Instructions: It helped to remove the small bracket that the brake lines
were attached to in order to keep the spindle from pulling on
the lines when you drop it in the next step.

- Remove the ball joint nut
Tools Needed: 22mm box wrench or very deep socket (I think, I had to use
an adjustable wrench for this one), Floor jack, Rubber
Mallet or Hammer with small piece of 2x4, 8mm socket
Instructions: This was the most frustrating part of the process, but still
not all that bad. First, you have to remove the nut from the
ball joint connecting the upper A-arm and spndle. This nut is
on pretty tight and takes a bit of work to remove, mine didn’t
spin because the taper was holding tight, but some WD-40
definitely helps the process along. It also helps to clean all
of the exposed threads as best you can before you start
taking the nut off. Once the nut is removed you have to
unseat the taper holding the parts together. Use the rubber
mallet to hit down on the control arm until it pops free. Use
the floor jack to support the spindle and lower A-arm.



- Remove factory shock
Tools Needed: N/A
Instructions: This step takes a bit of finesse. First you should drop the
lower A-arm/spindle as far as you can with the lift, making
sure that none of the brake lines are being pulled on. Next I
found it best to unseat the bottom of the shock from it’s
mount and reposition it so the bottom of the shock is as low
as you can get it behind the brake rotor. Next, have a buddy
push up on the upper A-arm to get it out of the way and
then guide the top of the shock out of it’s seat. It may take
a few tries, but you’ll get it.



- Swap out shock and place into assembly
Tools Needed: 2 sets of 2 strut spring compressors (not coil spring
compressors), Ratchet with 19mm standard socket and 4in
extension, 17mm box wrench, Ratchet with 8mm
socket, hammer, 19mm box wrench, 6mm hex wrench
Instructions: This is the step that scares most people about swapping out
their own shocks and the reason Rancho makes a bunch of
money selling their “Loaded” system. It’s really not bad, and
with a friend can be relatively painless. First thing to do is
mount the 4 spring compressors evenly around the spring.
Then evenly tighten them all down. It will take a bit of work
to get them all down, but you have to keep going until you
can feel the spring move around within the assembly. Once
the spring is loose, you can break the top nut free and
remove it while holding the hex head with the 8mm socket.
Once the nut is off simply remove the top shock seat, spring,
bumper, then knock off the bottom shock seat with a few
light hammer blows. The dust cover will get in the way of
removing the bottom seat, just let it rest against the bottom
of the cover and use the hammer again to knock it off as
well. Now, set your Bilstein to whichever setting you choose
and install the supplied shock mount seat. Push the bottom
shock mount onto the new shock and give it a few taps to
make sure it’s evenly pressed onto the seat. Add the bumper,
and additional supplied Bilstein hardware, replace the spring
and top shock seat. Make sure the spring is lined up properly
with the shock seats. Screw on the Bilstein supplied nut while
using the hex wrench to hold the shock rod. I’m not sure of
the exact torque required for this nut, but simply bottom it
out and I imagine the spring weight will hold it in place just
fine. After the nut is on you can remove your spring
compressors.



***Continued in next post

________________________________
2010 4x4 SCREW XLT, 5.4L, Bilstein 5100s (1.5" setting), Magnaflow 18" Catback, Volant Powercore CAI, 3.73, Weathertech, tailgate assist, Tint, USB2

Last edited by Action Jack; 04-01-2013 at 01:36 PM.
The following 7 users liked this post by Action Jack:
70-k5 (02-21-2014), BuffaloBlue (08-03-2020), Charlie63 (11-08-2020), Mass_Media (04-01-2013), mikep10175 (02-15-2014), o6S1D9e (05-11-2016), Vandicate (04-05-2013) and 2 others liked this post. (Show less...)

Popular Reply

04-03-2013, 11:30 PM
Buck183
Senior Member
 
Buck183's Avatar
 
Join Date: Aug 2012
Location: Siloam Springs, Ar
Posts: 360
Received 64 Likes on 38 Posts
Default

For future reference for all the DIYs out there. You will find this install much easier to do if you do not remove the steering knuckle from the upper ball joint. Instead remove the two lower control arm pivot bolts from the frame and let the arm separate from the frame removing the strut from the bottom.

When reinstalling the strut first attach the upper nuts loosely to the top of the strut tower. Then raise the lower control arm up to the strut and install the lower strut bolt. After this you just have to use a floor jack or transmission jack to raise the lower control arm back into place. Makes it much easier. Some kit instructions actually recommend doing it this way.

You don't have to fight the compression of the strut against the upper control arm while trying to get it reattached to the steering knuckle this way. You also don't risk over extending the half shaft by letting the weight if the assembly hang on it. They can be a pain to get back together when pulled apart.

I install 3-6 kits a week on late model F150s. It's about a 45 minute job for me to do both sides using this technique whereas the other way adds time to the install.

Food for thought....

Buck
Old 04-01-2013, 01:18 PM
  #2  
Junior Member
Thread Starter
 
Action Jack's Avatar
 
Join Date: Feb 2013
Posts: 23
Received 34 Likes on 6 Posts
Post Bilstein 5100 Install cont'd

***Sorry, ran out of space on the first post

- Replace lower shock mount bolt
Tools Needed: Ratchet with 27mm socket and 2in extension, 30mm box
wrench
Instructions: Very simple, just put the lower bolt back in place and hand
tighten



- Replace brake line bracket
Tools Needed: Ratchet with 10mm standard socket
Instructions: Replace the brake line bracket from where it was removed,
tighten until snug

- Reassemble upper A-arm and spindle
Tools Needed: 22mm box wrench, Ratchet with 8mm socket, Vise Grips
(Maybe)
Instructions: First step is to make sure the threads on the ball joint stud
and nut are as clean as possible. Next use some WD-40
great the threads a little. Assemble the ball joint stud
through the spindle and thread the nut on. Get the nut to go
as far as possible before the stud starts spinning with it. If
you’re lucky you will have exposed enough of the stud below
the bolt to get the socket on, if you’re slightly less lucky you
will have barely enough to get a set of vise grips on and if
there is nothing showing your patience will be tested. If
you’re able to get a hold of the stud just thread the nut all
the way back up and torque to 85 ft/lbs. If you’re have
trouble with the stud spinning just work the nut back and
forth quickly to try to get something to show, make sure not
to grab the taper or threads with your vise grips because this
is not a piece you want to have to replace.



- Tighten nuts on top shock mount
Tools Needed: Ratchet with 15mm deep socket, or ratcheting box wrench
Instructions: Tighten down the nuts you put on hand tight when you
installed the shock assembly. Torque to 47 ft/lbs



- Tighten lower shock mount bolt
Tools Needed: Ratchet with 27mm socket, 24”+ cheater bar and 30mm box
wrench
Instructions: Tighten down the lower bolt with a good amount of force.
The torque spec is 351 ft/lbs which your average torque
wrench won’t measure, but as long as you give a strong
steady couple of pulls with a cheater bar you will be close
enough.



- Tighten sway bar assembly
Tools Needed: 18mm box wrench, Ratchet with 8mm standard socket
Instruction: Replace the nut on the sway bar assembly and tighten down
to 66 ft/lbs.



- Double check everything
Tools Needed: N/A
Instruction: Make sure you don’t have any extra pieces and everything has
been properly torqued.

- Remount the wheels
Tools Needed: 21mm lug wrench
Instruction: Mount the wheels back on and torque lug nuts to 150 ft/lbs in
a star pattern.

- Alignment
Tools Needed: Shop
Instruction: Unless you have a lift and laser alignment device you’ll
probably need to take your truck in for this one. A local shop
should do the job for about $60 Note: Mine truck felt like the
alignment was fine after the install, but I took it in for an
alignment check and found out it wasn’t even close, so do
yourself a favor and at least get it checked, a lot of shops will
check for free.

- Reinspect
Tools Needed: N/A
Instruction: After about 75-100 miles of driving make sure to inspect all of
the nuts to make sure nothing has started to work its way
loose.

_______________________
2010 4x4 SCREW XLT, 5.4L, Bilstein 5100s (1.5" setting), Magnaflow 18" Catback, Volant Powercore CAI, 3.73, Weathertech, tailgate assist, Tint, USB2

Last edited by Action Jack; 04-01-2013 at 01:37 PM.
The following 10 users liked this post by Action Jack:
70-k5 (02-21-2014), boosted150 (04-04-2013), BuffaloBlue (08-03-2020), caneman88 (04-01-2013), dhardison (05-26-2017), Jeff B (12-25-2014), Mass_Media (04-01-2013), mikep10175 (02-15-2014), o6S1D9e (10-14-2021), TheFireman (08-25-2014) and 5 others liked this post. (Show less...)
Old 04-01-2013, 03:30 PM
  #3  
Senior Member
iTrader: (1)
 
Fx4_5.0Man's Avatar
 
Join Date: Aug 2011
Location: Winchester, Va
Posts: 461
Received 40 Likes on 38 Posts

Default

Good work on the write-up, I'm sure this will help a lot of people including myself. :_)
Old 04-01-2013, 04:00 PM
  #4  
Senior Member
iTrader: (1)
 
Waterfowler41's Avatar
 
Join Date: Nov 2010
Location: Naperville, Illinois
Posts: 885
Received 37 Likes on 31 Posts

Default

Hahahaha perfect timing with this my new shocks will be here this weekend. Time to find some strut compressors.

Thanks! Excellent write up!
Old 04-01-2013, 04:08 PM
  #5  
Member
 
Black Betsy's Avatar
 
Join Date: Jun 2011
Location: Michigan
Posts: 34
Likes: 0
Received 5 Likes on 4 Posts
Default

Nice job man. Thanks for the write-up. I've seen a write up on the rears before but not the fronts. Did you do them as well or just the fronts?
Old 04-01-2013, 04:19 PM
  #6  
0.9% is for suckers!
 
HoustonRider's Avatar
 
Join Date: Sep 2012
Location: Texas
Posts: 1,529
Received 172 Likes on 122 Posts
Default

nice write-up!
Old 04-01-2013, 10:06 PM
  #7  
Senior Member
 
Dundee_Dude's Avatar
 
Join Date: Sep 2010
Posts: 196
Likes: 0
Received 5 Likes on 3 Posts

Default

Great job. Thanks for taking the time to do this!
Old 04-01-2013, 10:37 PM
  #8  
Member
 
oxford-fx4's Avatar
 
Join Date: Sep 2012
Location: Canada
Posts: 80
Received 9 Likes on 8 Posts

Default

Amazing timing - 5100's are on their way!!!
Old 04-01-2013, 11:37 PM
  #9  
Elitism™
 
Mass_Media's Avatar
 
Join Date: Feb 2012
Posts: 46
Received 1 Like on 1 Post
Default

Perfect timing. I'm doing a level on mine and this is perfect. Thank you very much.
Old 04-03-2013, 10:02 PM
  #10  
Junior Member
Thread Starter
 
Action Jack's Avatar
 
Join Date: Feb 2013
Posts: 23
Received 34 Likes on 6 Posts
Smile The Results

Thanks guys. Good luck with all your installs. I ended up going with the 1.5" setting on my shocks and came out with just a little bit of remaining rake, about 3/4" to be exact. I think the 2.25 setting would have put me nose high, and since I plan on keeping my stock wheels and tires for a bit it would have left too much wheel well space. Anyway, here are the pics....

Before


After
The following users liked this post:
o6S1D9e (05-11-2016)


Quick Reply: The Definitive Bilstein 5100 DIY Install Thread



All times are GMT -4. The time now is 06:27 PM.