Ford F150 Forum - Community of Ford Truck Fans

Ford F150 Forum - Community of Ford Truck Fans (http://www.f150forum.com/)
-   Engine & Drivetrain (http://www.f150forum.com/f72/)
-   -   How To: Spark plug change-2004-2008 5.4 3V V8 (http://www.f150forum.com/f72/how-spark-plug-change-2004-2008-5-4-3v-v8-116291/)

kozal01 10-14-2011 10:34 PM

How To: Spark plug change-2004-2008 5.4 3V V8
 
Be advised! Neither F150Forum.com or myself will be held liable for any damages or injury's caused by doing this swap yourself. This is just a guideline for those that wish to save the money and do this yourself.




This is a hot topic around the forums but I have not found another full write up on how to do this swap here so I thought I would share my experience in the form of a "How To".

Here is a list of tools/ parts and other preparations I gathered before I did the swap. (your list may vary)

* Spark Plugs (I used the Motorcraft SP-515 Platinums. $9.50 from www.rockautocom)
* 9/16" Spark plug socket (I made my own with a 9/16" deepwell with a piece of rubber 1/4" ID hose in socket.)
* Various extensions, the plugs are pretty deep in the head.
* 10mm socket for removing the PCM and bracket
* 8mm wrench for to remove the battery cable
* 7mm socket for the bolts that secure the COP to the head
* Impact gun. I used a 1/2" drive but a 3/8" drive would work as well.
* PB Blaster penetrating oil
* Carb cleaner
* Air nozzle
* Dielectric grease
* Anti seize
* Lisle broken spark plug removal tool- part# 65600 (I got mine used online for much cheaper than a new kit)
* A cold beverage or two of your choosing.

http://i26.photobucket.com/albums/c1...008_174741.jpg
http://i26.photobucket.com/albums/c1...008_174724.jpg
http://i26.photobucket.com/albums/c1...008_174708.jpg
http://i26.photobucket.com/albums/c1...008_113315.jpg
http://i26.photobucket.com/albums/c1...008_113035.jpg
http://i26.photobucket.com/albums/c1...008_113013.jpg
http://i26.photobucket.com/albums/c1...008_112957.jpg

Ok Now that you have the supplies you can get started on the swap. To prepare myself for this I read thread after thread, watched video after video and talked to several people who have don this to find out what methods and tricks worked and what didnt and from that info I formed my plan.


First thing I did was warm up the engine, once its warm shut the engine off and disconnect the negative battery cable from the battery.

http://i26.photobucket.com/albums/c1...s/P1012178.jpg

Now unplug and remove the PCM and PCM bracket. Its on the firewall on the passenger side by the battery, it needs to come off so you can get to the rear plug on that side.

http://i26.photobucket.com/albums/c1...s/P1012177.jpg
http://i26.photobucket.com/albums/c1...s/P1012179.jpg
http://i26.photobucket.com/albums/c1...s/P1012180.jpg
http://i26.photobucket.com/albums/c1...s/P1012181.jpg

I used bungee cords to pull the PCM harness and other hoses back out of the way.

http://i26.photobucket.com/albums/c1...s/P1012189.jpg
http://i26.photobucket.com/albums/c1...s/P1012188.jpg

Also to free up some space I unclipped and removed this vacuum line and got that out of the way.

http://i26.photobucket.com/albums/c1...s/P1012190.jpg
http://i26.photobucket.com/albums/c1...s/P1012191.jpg
http://i26.photobucket.com/albums/c1...s/P1012192.jpg

Ok now that everything is out of the way its time to remove the COP's and COP boots from the spark plugs but before you do take your air nozzle and using compressed air blow out the pockets around the COP boots, alot of dirt and crud accumulates there and you dont want that falling down into the plug hole when you remove them. Once you remove the 7mm bolt that secures the COP and unplug it the COP will then pull right out with the boot attached to it. I numbered my COP's and layed them out in order out of the way.


http://i26.photobucket.com/albums/c1...s/P1012154.jpg
http://i26.photobucket.com/albums/c1...s/P1012155.jpg
http://i26.photobucket.com/albums/c1...s/P1012159.jpg

Ok now that the COP's are out of the way now you can start on the plugs themself.

http://i26.photobucket.com/albums/c1...s/P1012158.jpg

I used compressed air again to blow and dirt or crud that may have been in the plug hole under the COP boot just to be on the safe side. Now take your 9/16" plug socket with the extensions and a 3/8" drive ratchet and just crack each plug loose by hand, dont go any further than that.

http://i26.photobucket.com/albums/c1...s/P1012161.jpg

Next, grab your PB Blaster and Carb cleaner and shoot a bit down into each plug hole, dont go crazy with it but get enough in there to get the job done, just remember whatever you put in those holes will flow down into the cylinder after the plug is removed to dont use to0 much of it.

http://i26.photobucket.com/albums/c1...s/P1012160.jpg

Now, grab a beer or a coke and hang out for an hour or so to let the penetrating oil and the carb cleaner do their job.

Ok now that the fluids have had time to soak in and soften up the corrosion and carbon build up its now time for the moment of truth, grab your Impact, extensions and plug socket (I turned my impact down to the lowest setting and lowered the air pressure on the regulator to about 60 PSI) and start buzzing the plugs out. You will need to use a u-joint with your extension to get to the rear most plug on each side.

http://i26.photobucket.com/albums/c1...s/P1012162.jpg

I should have played the lotto today because all 8 of my plugs came out without a wimper.

http://i26.photobucket.com/albums/c1...s/P1012168.jpg
http://i26.photobucket.com/albums/c1...s/P1012185.jpg
http://i26.photobucket.com/albums/c1...s/P1012198.jpg
http://i26.photobucket.com/albums/c1...s/P1012167.jpg

Ok now at this point, hopefully you have had the same success as I had and you can breath a sigh of relief and be ready to install the new plugs. If you werent so lucky its time to break out the Lisle tool and go to town. (if anyone reading this that has successfully used the broken plug extractor please chime and and tell your experience)

Next, grab your new plugs and your anti seize and coat the end of each plug with a thin coat of anti-seize. There is some debate about whether or not to coat the threads, I chose not to but its up to you.

http://i26.photobucket.com/albums/c1...s/P1012171.jpg
http://i26.photobucket.com/albums/c1...s/P1012173.jpg

Now drop the plugs down into the holes and torque them down to the proper spec. (25 inch pounds)
Now clean any dirt and grime off the COP boot paying attention to the end that goes over the plug, if there is any old dielectric grease on it clean that off and apply new grease to the boot and COP spring. Once that is done drop the COPS back into the plug holes and fasten them back down. (dont forget to plug them back in) Re-assemble the vacuum line (s), PCM bracket and PCM and re-connect the battery. Now youre ready to start the truck and see how it runs!

http://i26.photobucket.com/albums/c1...s/P1012193.jpg

After it fires up and purrs like a kitten grab another cold beverage, stand back and admire your work knowing you just saved yourself $500 to $1000 by doing this yourself! (I had $116 into parts and supplies not including tools and beer)

http://i26.photobucket.com/albums/c1...s/P1012195.jpg


After doing this swap successfully I can honestly say this is one of the easiest plug jobs ive done thus far on any vehicle. Had any broke that would have added another degree of difficulty but if your a do it your selfer like I am and youve been thinking about doing this yourself dont let it intimidate you. Just do as I did and prepare for the worst but hope for the best. Hope this write up helps somebody. Good luck!

Scottsred11FX4 10-15-2011 12:11 AM

Very nice write up. You da man!

mike18 10-15-2011 12:28 AM

sweet write up!

kozal01 10-15-2011 05:54 AM

Thanks guys

kozal01 10-15-2011 07:06 AM

Plug torque should be 25 ft-lb's not in-lb's, that was a typo.

ToughFX4 10-15-2011 11:11 AM

Great write up! Lot's of good info here! Thanks :thumbup:

jbhill 10-15-2011 12:55 PM

this is finally what we have ben looking for! i plan on doing mine next weekend, so this helped a TON. also im assuming you put the carb cleaner in with the pb blaster to thin it out and so it will combust once you fire it up. you could blow it out instead.

kozal01 10-15-2011 01:28 PM

Quote:

Originally Posted by jbhill (Post 1131165)
this is finally what we have ben looking for! i plan on doing mine next weekend, so this helped a TON. also im assuming you put the carb cleaner in with the pb blaster to thin it out and so it will combust once you fire it up. you could blow it out instead.

No I used the carb cleaner to help break up the carbon build up on the tip of the plug. A mechanic friend of mine said he does the PB Blast with carb cleaner mix whenever he does these plug swaps. His theory is if there is any corrosion on the long part of the plug the PB Blaster will penetrate and loosen that and then the carb cleaner will take care of the carbon build up. He said he has been very successful using that method so I copied him.

wsybert 10-16-2011 01:19 AM

Thanks for the write up. Very helpful, as I tackled mine today. I was able to get 5 out of 8, without breaking. I was very optimistic when I got 1-4 out without issue...then #5 broke.

The nut broke from the tip, but the porcelain stayed intact. That kind of threw me, as I couldn't figure out what was going on. Once i did, I used some long needle nose pliers to pull the nut up and out, then broke the plug and pulled it out. Used the Lisle tool to do the rest. Worked very well, and took me about an extra 15 min per, on the broken ones. 6 was fine, then 7 & 8 broke. 8 was a little bit of a PITA, due to accessibility, but not too bad.

I used Champion 7989 platinum plugs. Got them and the Lisle tool for $100, from a guy who bought them, then sold his truck.

My truck has 86k miles, and had a miss that was bugging me. Now it runs like new!

kozal01 10-16-2011 12:07 PM

Quote:

Originally Posted by wsybert (Post 1132157)
Thanks for the write up. Very helpful, as I tackled mine today. I was able to get 5 out of 8, without breaking. I was very optimistic when I got 1-4 out without issue...then #5 broke.

The nut broke from the tip, but the porcelain stayed intact. That kind of threw me, as I couldn't figure out what was going on. Once i did, I used some long needle nose pliers to pull the nut up and out, then broke the plug and pulled it out. Used the Lisle tool to do the rest. Worked very well, and took me about an extra 15 min per, on the broken ones. 6 was fine, then 7 & 8 broke. 8 was a little bit of a PITA, due to accessibility, but not too bad.

I used Champion 7989 platinum plugs. Got them and the Lisle tool for $100, from a guy who bought them, then sold his truck.

My truck has 86k miles, and had a miss that was bugging me. Now it runs like new!

Im glad it helped you. Good to know the extractions went well. Did the porcelain break off on any of them?


All times are GMT -4. The time now is 06:02 AM.


Copyright 2006 - 20011 F150forum.com