Bellltech 4" flip for 04 up trucks
02-22-2014, 02:03 AM
#1
F150 SUSPENSION GURU
Thread Starter
Bellltech 4" flip for 04 up trucks
Guys cant get it to upload it up but if you want the directions shoot me a email to tony@tbssowners.com i will forward it to you.
Last edited by NORCAL SS; 02-24-2014 at 09:49 PM.
02-22-2014, 09:32 PM
#4
Senior Member
I'm interested in this do you have the part number? Will it work with a 2014 with a 2 piece driveshaft?
03-02-2014, 01:58 AM
#7
Senior Member
I got the install directions for this kit from tony! it looks good. But you will half to Modify the Carrier bearing mount by cutting out the OEM Holder..then drilling some holes in the crossmember I think...to mount the new one! More Complex then the other kits are. and u also gotta drill a hole in the frame for one of the shackle hangers also. Not too keen on cutting and drilling holes. would be harder to switch back to stock with the carrier bearing mods you half to do...
...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/
...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/
Trending Topics
03-02-2014, 08:36 AM
#8
I got the install directions for this kit from tony! it looks good. But you will half to Modify the Carrier bearing mount by cutting out the OEM Holder..then drilling some holes in the crossmember I think...to mount the new one! More Complex then the other kits are. and u also gotta drill a hole in the frame for one of the shackle hangers also. Not too keen on cutting and drilling holes. would be harder to switch back to stock with the carrier bearing mods you half to do... ...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/
...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/
03-03-2014, 10:15 AM
#10
Senior Member
I got the install directions for this kit from tony! it looks good. But you will half to Modify the Carrier bearing mount by cutting out the OEM Holder..then drilling some holes in the crossmember I think...to mount the new one! More Complex then the other kits are. and u also gotta drill a hole in the frame for one of the shackle hangers also. Not too keen on cutting and drilling holes. would be harder to switch back to stock with the carrier bearing mods you half to do... ...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/
...thought this would be a nice bolt on kit with no major cutting and drilling involved! now I'm stuck on going with DJM's kit or just getting the full BellTech 3/5.5 kit! *SIGH* .........:/I have to correct myself, this is not required for single cabs with no carrier bearing and 1 piece driveshafts. instead they give you a shim for your trans. But on vehicles with 2 piece drive shafts you do have to cut.
Last edited by azmidget91; 03-03-2014 at 11:13 AM.