How do you remove the...? - Ford F150 Forum - Community of Ford Truck Fans



How do you remove the...?

Reply
 
 
 
Thread Tools Search this Thread
Old 12-01-2009, 09:46 PM   #1
Senior Member
Thread Starter
 
david350's Avatar
 
Join Date: Sep 2009
Location: Bradenton FL
Posts: 368
Thanks: 0
Thanked 0 Times in 0 Posts
Default How do you remove the...?

...Fuse box covers.

Am I missing something? The one under the hood is on tight, how am I supposed to get it off, it wont come out of the clip.

...Door panels.

I want to check out my speakers. Don't see how you are supposed to take the door panels off.


It's a '99 4x4 5.4. Thanks!
david350 is offline   Reply With Quote
Old 12-01-2009, 10:10 PM   #2
Member
 
Join Date: Sep 2009
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Default

havent had my door panels off yet but from experiances on many other fords theres probably push pins all along the sides.take a screw driver and try and pry up the bottom a little bit and look in and see whats holding it. also probably a couple screws near the interior handle
as far as the fuse panel cover try using a screwdriver to work the clip from the bottom should just pop off
rich08 is offline   Reply With Quote
Old 12-01-2009, 10:12 PM   #3
Senior Member
 
Big. D's Avatar
 
Join Date: Nov 2009
Location: Allentown
Posts: 338
Thanked 1 Time in 1 Post
Default

I can help you with the rear door panels on the supercab. Unscrew the pop out window mechanism. Take a flat screwdriver (some tape on it so you don't scratch or mar anything) and go under the upper panel, you should be able to see the clips and push on them to pop off the upper panel. Then there's a plastic rivet, 2 screws, and a nut that has to be removed on the top of the lower panel. After that lift up on the lower panel and then pull out.
Big. D is offline   Reply With Quote
Old 12-01-2009, 10:15 PM   #4
Senior Member
 
Join Date: Aug 2009
Location: Apex, NC
Posts: 452
Thanks: 0
Thanked 0 Times in 0 Posts
Default

what do you do after you drill through a plastic rivet? do you put a new plastic rivet in?
atvrider93 is offline   Reply With Quote
Old 12-01-2009, 10:19 PM   #5
Senior Member
 
Big. D's Avatar
 
Join Date: Nov 2009
Location: Allentown
Posts: 338
Thanked 1 Time in 1 Post
Default

Here's the front panels,
http://www.brucehartman.net/2007/01/...-a-2000-f-150/
I remember the rear panels from a speaker installation guide but i can't remember where i saw it. For the plastic rivets i believe that if you pushed down on the center first and then wiggled it out you could get it without breaking it.

When you reinstall panels make sure that no wires are caught under panel clips. I had to search for a short in my left rear speaker. When the rear pillar trim was put on by ford the one panel clip caught a wire and rubbed through the insulation which in turn caused a short against the frame.
Big. D is offline   Reply With Quote
Old 12-01-2009, 10:46 PM   #6
Senior Member
Thread Starter
 
david350's Avatar
 
Join Date: Sep 2009
Location: Bradenton FL
Posts: 368
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Thanks for the replies, and link.

For the fuse boxes I'm going to have to work at the one under the hood with a screwdriver like you said, but the one under the steering wheel is covered up... I need to get to fuse 25 to check it and it's under a black cover.
david350 is offline   Reply With Quote
Old 12-02-2009, 12:40 AM   #7
Senior Member
5 Year Member
 
ONELOWF's Avatar
 
Join Date: Oct 2009
Location: Nevada
Posts: 232
Thanks: 0
Thanked 1 Time in 1 Post
Default

The fuse box under the hood has plastic clips that are against the inner fender, and hard to see. You should not need a screw driver.
ONELOWF is offline   Reply With Quote
Old 12-02-2009, 12:52 AM   #8
Senior Member
 
Join Date: Aug 2009
Location: Apex, NC
Posts: 452
Thanks: 0
Thanked 0 Times in 0 Posts
Default

the one under the steering column is pretty easy if I remember right. you basically just pull the cover off
atvrider93 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
How To: 2015 F-150 Front Bumper/Tow Hook Removal boozinbuzz 2015 - Present Ford F150 7 06-02-2016 02:25 AM
INTAKE MANIFOLD GASKET FAILURE on my 2008 Ford F150 Crew cab 4X4 4.6 litre Pipercub1 General F150 Discussion 2 09-14-2015 06:27 PM
INTAKE MANIFOLD GASKET FAILURE 2008 Ford F150 Crew cab 4X4 4.6 litre Pipercub1 2004 - 2008 Ford F150 0 09-14-2015 03:15 PM
1989 to 1996 Ford F150 4x4 E4OD transmission rrmoval writeup notsosporty98 Drivetrain 3 09-12-2015 07:02 PM
INTAKE MANIFOLD GASKET FAILURE 2008 Ford F150 Crew cab 4X4 4.6 litre Pipercub1 2004 - 2008 Ford F150 0 09-12-2015 05:00 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 08:53 AM.


Copyright 2006 - 2016 F150Forum.com