Engine Builders talk.
08-08-2014, 04:57 PM
#2671
Senior Member
Thanks. I think I could rush it and have the cheapest L Swap but I plan on going bigger from the beginning. I still plan on porting the charger, plenum etc, efans with the H/E, LTs, alum radiator. I probably won't start buying big items again until next fall.
Still need fuel pump, hE, alt, gaskets l, throttle cable, all bolts, water pump setup, IAt ext
And need all hoses, lines, brackets and fitting to hold everything.
What am I missing?
I feel like I've forgotten everything I have researched
08-08-2014, 06:20 PM
#2672
Check out www.car-parts.com for the cables and brackets. Search for Harley & lightning trucks. Unless someone is doing a part out, they're hard to find. I may be able to get you the bolts from a guy on the FB page. If I run across anything else, I'll let you know. Owe you one for find on the 6lb lower anyways!
Thanks man. I'll keep an eye out for your list.
What fuel pump did you go with?
08-08-2014, 06:33 PM
#2673
Senior Member
I ended up getting a pair of Walbro 255's with stainless Y with the hat from a guy on LR doing a part out. Also ended up getting all the bolts, vacuum assembly, alternator bracket and pillar pods from him.
08-08-2014, 06:41 PM
#2674
Www.car-parts.com is the site. I searched for an alternator in the south east and located a salvage yard that had a wrecked harley. They had already pulled the engine, but they had the throttle & cc cables with the bracket.
I ended up getting a pair of Walbro 255's with stainless Y with the hat from a guy on LR doing a part out. Also ended up getting all the bolts, vacuum assembly, alternator bracket and pillar pods from him.
08-08-2014, 07:01 PM
#2675
Senior Member
08-08-2014, 07:20 PM
#2676
Senior Member
08-08-2014, 07:21 PM
#2677
08-08-2014, 10:30 PM
#2679
Remaining:
Fuel parts
Metco Fuel Rails
Aeromotive/Fore regulator
-8AN feed lines
-6AN return lines
-8AN rail fittings
-6AN rail fittings
Fuel Hat bulkhead fittings
88# deutchworks injectors
Turbo and exhaust parts:
SS manifold bolts
-10 drain lines
-3 Fee lines
2 x -10 Bulkhead connectors for oil pan
Down Pipe all the way back to duals
Cold side pipe (Dual 2.5 inch) into one 4"
AFCO Heat exchanger
Coolant Pump and hoses
Coolant reservoir
Silicon couplers
Two 1/4NPT Tees for feed lines
38mm tial wastgates
BOV
SCT BA3000
Misc:
Alt
Alt Bracket
Need to wire up gauges
Install Pods
Start up tune
SCT Tuner
Download tranny controller system.
Various vaccum and boost lines
Lots more budwesier
Shew feels like I was getting close, but dang thats a lot of parts.
I need to add up my totals.
Fuel parts
Metco Fuel Rails
Aeromotive/Fore regulator
-8AN feed lines
-6AN return lines
-8AN rail fittings
-6AN rail fittings
Fuel Hat bulkhead fittings
88# deutchworks injectors
Turbo and exhaust parts:
SS manifold bolts
-10 drain lines
-3 Fee lines
2 x -10 Bulkhead connectors for oil pan
Down Pipe all the way back to duals
Cold side pipe (Dual 2.5 inch) into one 4"
AFCO Heat exchanger
Coolant Pump and hoses
Coolant reservoir
Silicon couplers
Two 1/4NPT Tees for feed lines
38mm tial wastgates
BOV
SCT BA3000
Misc:
Alt
Alt Bracket
Need to wire up gauges
Install Pods
Start up tune
SCT Tuner
Download tranny controller system.
Various vaccum and boost lines
Lots more budwesier
Shew feels like I was getting close, but dang thats a lot of parts.
I need to add up my totals.
